Jump to content
SAU Community

Recommended Posts

Yeah been thinking about that too!

It seems to me the easier option straight up if you already have the supporting mods. Then if it's still not what you want, upgrade turbo and you're already on E85 :)

It seems to me the easier option straight up if you already have the supporting mods. Then if it's still not what you want, upgrade turbo and you're already on E85 :)

How much did it cost to convert to E85?

And do you know how much it costs to go a full flex-fuel setup? I assume you need a new ECU as well? Dont think Nistune will do it

alcohol is for drinking. oil is for driving.

f**k the enviroment yo.

^^ Pommy prick pretending to be a mullet eating bogan. Just because your dinosaur V8 goes backwards in power on ethanol. :P

With some decent comp and drilling the jets on your carby I could possibly get some more powers out of your clunker Paul...

^^ Pommy prick pretending to be a mullet eating bogan. Just because your dinosaur V8 goes backwards in power on ethanol. :P

With some decent comp and drilling the jets on your carby I could possibly get some more powers out of your clunker Paul...

wadda ya mean pretending?

tank is a tank. dont need more power. just needs a s bigger gun.....

How much did it cost to convert to E85?

And do you know how much it costs to go a full flex-fuel setup? I assume you need a new ECU as well? Dont think Nistune will do it

If you have the overhead in your fuel system, it costs nothing... Forget the flex fuel for now, just get on it...

If you have the overhead in your fuel system, it costs nothing... Forget the flex fuel for now, just get on it...

Probably not.

My fuel pump i got serviced about 3 years ago via Sabbadin Automotive. All it said on the invoice was a Hi Flow Walbro fuel pump. Don't even know what model it is

How much did it cost to convert to E85?

And do you know how much it costs to go a full flex-fuel setup? I assume you need a new ECU as well? Dont think Nistune will do it

need to go a haltec/link/vipec etc if you want flex fuel. changing to that is quite a few $$$ as its sensor + two tunes + ecu, you would also want the ecu controling boost as you can run a heap more on E85 than 98.

How much did it cost to convert to E85?

And do you know how much it costs to go a full flex-fuel setup? I assume you need a new ECU as well? Dont think Nistune will do it

$500 for the tune

My engine already had the supporting mods; I had planned for ethanol eventually a long time ago. Supporting mods = basically just a big enough fuel system. 555s and a 040 will do you safely up to 300rwkw.

Also, fk flex fuel. Just get tuned on United which is consistently E85 afaik. There's one in Clayton and one in Scoresby you can fill up at. Car runs beautifully; I don't even have a wide band.

$500 for the tune

My engine already had the supporting mods; I had planned for ethanol eventually a long time ago. Supporting mods = basically just a big enough fuel system. 555s and a 040 will do you safely up to 300rwkw.

Also, fk flex fuel. Just get tuned on United which is consistently E85 afaik. There's one in Clayton and one in Scoresby you can fill up at. Car runs beautifully; I don't even have a wide band.

With Flex fuel more so thinking on long trips and the ability to use any fuel you want

So say your driving on a long trip you got 1/4 fuel of e85 left. You fill up the rest with 98octane since there is no e85.

Load up the map for 98 octane

Is it still ok to drive with a mix of 98 and e85 or?

if you want NA power on e85 you need to go 12-14:1 compression, but then you can never go back to 98.

itd be interesting to see if my tuned for 98 ls1 would run on a 10% ethanol fuel... not that id try it... but itd be good to every now and again not have to spend so much on 98.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...