Jump to content
SAU Community

Recommended Posts

but gtst are cast alloy are they not?

strong misinformation you share. Make stupid people you will..

Shhh :P

best I can do is in my build thread. just one pick.

was hoping for 1 photo from winton, but you know how it is: pulsar lucky to get one photo from a whole day of driving let alone out for 2 sessions.

Paint gayside blue, put GTR badges on and some not so clever custom plates. You'll have full blog posts of the same angles over and over :P

  • Like 1

Sif no 20's, I have an angle grinder here...

darren is serious about that micra mate, hes just joined the site and asked the flamin mongrel to drop his price.

this is the dick that was questioning the power

Reduce your taxable income by $100 = hardly worth the time it takes to enter it lol. Hope you kept your chair receipt too, haha.

E-tax is shitting me up the wall. Won't lodge return cause can't match MyGov account, WTF

Also NIB gave me 40% government rebate instead of 30%, f**ktards, so now have to pay $155 back...which I can't eliminate with deductions because as I add/increase them, my offsets get reduced.

Oh well, all tax back minus $155 is pretty good. Now if I can just lodge the fker :/

haha yeh not just that but every little thing counts

didn't get as much back as last year myself but can't complain with a couple of k :D

you should of gotten a fair bit back yeh cos you weren't working a few months? that's what happened to me last year

Edited by UNR33L
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...