Jump to content
SAU Community

Recommended Posts

In November 2010, The Weekend Australian reported that "Treasury officials preparing the so-called Red Book of briefs for the incoming government were as divided as private sector economists about the strength of the property market."

In December 2010, an MLC investments strategist observed that "residential property looks absolutely obscenely overvalued and seems to offer very, very poor investment prospects."

In March 2011, Morgan Stanley global strategist Gerard Minack said that "we've had 20 years where the Australian consumers have been willing to borrow more to buy an asset that they believe always goes up in value. The classic sign of an asset bubble." and that "home prices are 30 to 40 per cent above fair value."

In October 2009, it appeared that the pricing of homes was being inflated by actions taken in October 2008 aimed at addressing the fallout from the GFC. Housing was identified as an asset class worth shoring up against the type of deleveraging seen in the stockmarket.

The government increased assistance given to first home buyers as part of its 'Economic Stimulus Strategy',. A substantial reduction of RBA interest rates also played a part in maintaining prices

2010: November - The RBA raises interest rates 0.25% to 4.75% citing the "economy is now subject to a large expansionary shock from the high terms of trade"

2011: February - New housing loans approved by Australian banks fall 5.6 per cent to a 10-year low in February.

2011: March - Prosper Australia launches a campaign for a "buyer's strike" in an effort to drive down prices.

2011: April - Melbourne median home price falls by $36000 (6%) to A$565,000 in March Quarter.

2011: May - The number of properties for sale in Melbourne double.

2011: June - Number of home loans in arrears 90 days overdue, rises to 15 year high.

sheep-falling-off-cliff.jpg

ill post in here before putting it on carsales. so my evo 8 MR for sale looking for $31,000 NEG. if interested pm me for full details :)

Have a friend who might be looking for an Evo 7 or 8, will show him your car.

Do I get some sort of reward or finders fee? :D

I <3 left over pasta... Always tastes better the next day!

Agreed. Don't know why but they do taste better...

I like my meat fresh. Just sayin.

you get a bj from scott.

you get a big hug and a beer or 2 or 3 :D

that will happen after i feed him those beers :P

Let's just stick to hugs and beers :P

At a higher price then the rest of those fried chicken places.

But I always get Classic Burger with Beacon / Cheese / Egg and a serve of 8 BBQ Ribs.

IDE rather pay the little extra and have food that stays in my stomach rather than coming back up

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...