Jump to content
SAU Community

Recommended Posts

Word of mouth is the most powerful tool for businesses. If everyone comes out of his shop and starts to recommend him, then he must be doing something right, no?

And what about those that dont recommend him coming out of his workshop? I had two PMs about it? 'everyone' ... lol

Sorry I knew I shouldnt have said everyone. I forget that I'm speaking publicly sometimes.

None the less, the only way to find out is to try for yourself.

I think we're all grown ups here, make your own decision and don't get all emotional if a workshops name gets dropped in a conversation. It's their decision isn't it? Not yours.

Besides if you were to substitute unigroup with workshop that you like, then I'm sure you'll be backing them up. And someone will come out and say "nah x workshop is better".

This is basically politics. Pointless to discuss.

I wanted full boost before 4k and was going to get cam gears but was assured i wouldnt need em.. and he did pull it off.. 25psi by 4k is pretty awesome..

They would have tried around 20psi... Id say it would have been around 310kw.. will check tomorrow

25psi at 4k is pretty impressive. I dont think i've seen anyone here hit that level of boost at 4k, normally would be 20-22psi and that would be with adj cam gears.

I personally was able to get about 18psi at 4k (stock gears) but that was with no boost source to the actuators(8.8psi) and they had a reasonable amount of preload on them so i doubt they were being pushed open.

Have a boost plot against rpm?

Not sure now.

I bought my 5 speed with big input shaft for $2,760 delivered from greenline 4 years ago. You will need all the Series 3 internals to run it.

Make sure you buy the billet centre plate from OS.

Not sure now.

I bought my 5 speed with big input shaft for $2,760 delivered from greenline 4 years ago. You will need all the Series 3 internals to run it.

Make sure you buy the billet centre plate from OS.

That is pritty cheap. I wish they didnt come with such tall ratios

That is pritty cheap. I wish they didnt come with such tall ratios

They can either work for or against you. At Huntley it really works. You just need a bigger engine to turn the cogs. *hint hint, nudge nudge* ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...