Jump to content
SAU Community

Recommended Posts

Do you run coilovers? Have your rears scrubbed out when crabwalking really steep driveways? I want 265's on the rear now...

no coilovers just really really low springs and they havent scrubbed on steep driveways, only scrubs on big bumps if im going fast enough

dont get +40 pinch.gif atleast get +35 or somewhere around that

even with my 9.5 +34 i could go atleast +30 without rubbing and still they wouldnt stick out.

Hmm.. so what would you recommend out of these two:

18x8.5 +35 Front and 18x9 +32 Rear

OR

18x8.5 +35 Front and 18x9.5 +40 Rear

No guard rolling, don't want it to scrub of course either.

With your idea, would going for a +32 (even if it's 9") be a better fitment to the outer guard? Not really after "big width" rather just a nice look.

  • 1 month later...

I am having the same problem with getting my head around all the offsets etc..

Im looking at getting 19" x 9.5 +22 but im not sure if they will fit.. Everyone else seems to run 18"s only.. I just want something different..

My car has coilovers but is at about standard height.. The body kit should make it look like its a bit lower to the ground as I dont want to lower it because they wheels may not fit with out rolling the guards..

Pics would be sweet when you get it done :yes:

Running cr kai's - F: 18x8.5 + 30 (from memory) with 225 rubber R: 18x9.5 + 38 with 265 rubber.

Conservative (no rubbing issues), fill the guards with no work done, look nice. Excuse quick photo (bad quality)

post-76525-0-68194600-1331522485_thumb.jpg

Edited by TM7GTR

I could do with a bit of advise.

About to buy TE37's:

Front: 18" 8.5 +30

Rear: 18" 9.5 +40

Am I going to have any issues?

Will be fine, exactly what I am running except my rears are +38 offset. +40 is the offset of the stockies I believe

The only issue you're going to have is that the wheels have flat spokes :down:

The fronts will be fairly flat but my rears have a bit of concavity, and only 2 offset lower.

TE37's are pretty exxy though, have you looked at Varrstoens's or Rota Grids?

The fronts will be fairly flat but my rears have a bit of concavity, and only 2 offset lower.

I have never seen 9.5s in that offset with concavity :huh:

18x9.5 +22 at the back will sort that out though :thumbsup:

TE37's are pretty exxy though, have you looked at Varrstoens's or Rota Grids?

:sick:

The TE37 is a proven strong, light wheel that is FAR superior to the above mentioned.

I have never seen 9.5s in that offset with concavity :huh:

18x9.5 +22 at the back will sort that out though :thumbsup:

:sick:

The TE37 is a proven strong, light wheel that is FAR superior to the above mentioned.

They aren't crazy concave of course, but they are far from flat. TE37's easily one of the best ever, and the cost reflects so.

The only reason I mention it, is I've found a set for $2500 delivered, seem alright condition, in the above offset I mentioned.

So as long as +40 will fit, I'll deal with the cosmetic aftershock. At least they will fit nicely, regardless of the outter face concavity.

I hope. ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...