Jump to content
SAU Community

Recommended Posts

i wave to damn near every skyline i see, and 90% of the time i get a wave back :D not so much as a ford n holden kinda thing, i just wanna congratulate all the other ppl that i see on the road on their fine choice of car :D

Spot on bud, i think we all have to have a special connection to pilot a skyline!!!

EMZ

Edited by EMZ R33
  • Replies 7.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Spot on bud, i think we all have to have a special connection to pilot a skyline!!!

EMZ

always used to wave when i seen ya bud..........used to get round in a red 31 with black drifteks

look out for a red ute ever waving or flashing lights.............theres SAU stickers all over it LOL

yes, yes i do...

south and torrens rd? that liberty got messed up. I reckon that must have been a fatal one. cops blocked off the intersection. was holding up traffic bad.

Madaz.. I take it seeing as you know my car, and saw that accident this morning, u must also work near mile end....?

EDIT: just saw the accident on the news, he ran from the cops and got cleaned up. not fatal, but pretty messed up. they said they raided his house and recovered 2 stolen cars, and they showed a nissan ceffy.... anyone lost one lately?

yeah that ceffy is a guy off NS.com apparently still in one piece too.

i have no symapthy for the guy that got hit karmas a whore

lauren

always used to wave when i seen ya bud..........used to get round in a red 31 with black drifteks

look out for a red ute ever waving or flashing lights.............theres SAU stickers all over it LOL

hahahah yeah, i have copped the flash n wave treatment on seacombe road :whistling:

i wave to damn near every skyline i see, and 90% of the time i get a wave back :D not so much as a ford n holden kinda thing, i just wanna congratulate all the other ppl that i see on the road on their fine choice of car :)

well could you imagine holden n fords waving to each other, there arm would be dead from waving to every old man n lady dropping there kids off in town. i mean there so damn common when their clubs roll past it takes bout 20 of them to go past before you realize its a club.

spotted miss 34 pulling out of pooraka maccas onto main nth about 5ish? nice car.

i was, um how would u say, taking a short cut, so i err, wouldnt have to wait at the lights? hehehehe :)

SPOTTED THIS ARVO

4.35pm Burgundy R33 Gts heading north on Main North Rd, Enfield.....pretty girl with long brown hair......needs a wash badly (the car, not the girl).

6.00pm Nice black R32 Gtr heading north on Hampstead Rd......car looks very tuff.

6.15pm Dark coloured R33 heading north on Fullarton Rd......nice rims.

6.30pm Black R33 heading north on Goodwood Rd......bling FMIC.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...