Jump to content
SAU Community

Recommended Posts

yeah, just gonna give it a mad degrease and scuff back and hit it with some of the new mix and some 15min clear.
planning on doing that saturday morning, motor in saturday night.

should be fully off da chain


need to know the factory paint code for the airbox..
gonna paint strip it and repaint it

future ref: Nissan Navara D21 Mechanical speedo sender Part No. 32702-02G17

japan auto 1 on railway road epping.
spoke to the ever so fabulous kenan from edge motorworks.
they will give it a go over and start it for me. not long to go

  • Like 1

japan auto 1 on railway road epping.

spoke to the ever so fabulous kenan from edge motorworks.

they will give it a go over and start it for me. not long to go

you see any micras in the wreckers moh? :woot:

Took us two hours to get that flamin mongrel out with the box

:O

When my mate and I took a crack, it took us forever to take it out.

went to work on saturday, ended up in geelong at the shannons classic show

then came home to find this in my drive way
1477804_10202624183548735_1777608622_n.j

quickly got to work!

1455201_10202625435260027_106380254_n.jp

1471783_10202625435540034_1260255376_n.j

my right hand man Youssef helping out as always!
154697_10202625418019596_2877087_n.jpg

and monday was a good day!
1455155_10202636864465750_578359387_n.jp
601553_10202636866105791_763643673_n.jpg


thats all for tonight.
currently stripping the RB20 of all the bolt ons for cleaning and fitting to the RB26, just need to bolt up the extra lines. finish the plumbing, do the shaft and were ready to f**king go!

1460244_10202638295981537_273636787_n.jp


also heard you can use the rb20 mounts for the rb26, mine are fouling on the oil pressure switch. do i need to trim it or am i doing it wrong?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...