Jump to content
SAU Community

C34 Stagea Front Driveshaft Interchangibility..

driftrx

By driftrx,
in Four Door Family & Wagoneers

 Share

Recommended Posts

driftrx Collaborator

driftrx

Posted
Posted

heya guys and gals.

spent the last 45 minutes fishing around for info on this... however every link that looks like it would lead me to the answers i need on here appears to be dead.

basicly. what front driveshafts/CVs are interchangable with my s1 c34 stagea? (r32/33/34 gtr?)

mine are absolutily shagged. clunk around corners, shudder at speed etc. between that and my shagged CAS the cars turned into a pig to drive.

if anyone can steer me in the right direction, much appreciated.

dan

Duncan Grand Master

Duncan

Posted
Posted

I have not fitted one personally, but I am sure 32/33 and probably 34 driveshaft will be interchangeable.

The gearbox, block and diffs are all interchangeable, so the driveshaft must be too.

driftrx Collaborator

driftrx

Posted
  • Author
Posted

thats good to hear.

dont want to get a set of 33 gtr ones for example and find they have different splines for example...

ill keep digging around untill i find someone definitely confirming it however.

driftrx Collaborator

driftrx

Posted
  • Author
Posted

are S1 and S2 front CV's the same?

are they different for the S2 RS Four S?

id say they'd be the same throughout the whole range.. (pending that 32/33/34 ones all fit that is)

im still on the hunt for a pair from a gtr. ill report in to confirm they do fit.

  • 5 years later...
Stagea_Neo Experienced

Stagea_Neo

Posted
Posted (edited)

Update to an old thread.

I heard they are the same as a GTS-4.  

Also heard more recently a Pathfinder uses the same shafts up front, possibly just the inner's, 

I will clarify next time I chat to the mechanic.

 

Pete

Edited by Stagea_Neo
Stagea_Neo Experienced

Stagea_Neo

Posted
Posted

Spoke to the mechanic, only the left cv shaft is the same.

I just purchased a right cv shaft from Paul at Osaka Imports in Knox, Vic. (very helpful and friendly).

He has a left/passenger side shaft there if anyone needs one. (my left was ok).

Apparently it's the right side that usually go's.

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...