Jump to content
SAU Community

Recommended Posts

Hey guys, just prepping my car for a track meet and need to resolve an issue with the powersteering. Last time I was at Wakefield, the powersteering fluid bubbled over and spat out of the reservoir. It looks like the felt washer for the cap needs to be replaced, but what else can i do to ensure the powersteering fluid doesn't overheat again? Is it a common issue with track GTR's? And where can i find this felt washer??

Cheers!

Hey Jimmy,

There was another thread with this mentioned recently but i cant remember where, there were people putting socks over the resivior and a couple of other solutions, maybe search for it but it was helpful info from memory :)

If you're not using it already, fully synthetic ATF has a higher boiling point than regular stuff. It might be enough for you.

I was already using ATF so I suppose an oil cooler is required! I guess it's an issue with these cars then? Also where can i find that washer?

Thanks guys

Could probably try Amayama.com and search for it too mate....

On a sort of related note, is this thing a cooler or dampner? I never really looked too hard at it -

post-47580-0-33980300-1340754129_thumb.jpg

i believe that its a cooler due to its location, as said above, throw a trans cooler at the power steering and it wont boil on you again

Edited by StevenCJR31

Thanks guys, for those that have installed a cooler on the powersteering, any chance you could post a photo of where you stuck it? There's not much room in my engine bay

Thanks guys, for those that have installed a cooler on the powersteering, any chance you could post a photo of where you stuck it? There's not much room in my engine bay

LH Guard

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...