Jump to content
SAU Community

Recommended Posts

I am in the middle of buying/building my new RB26/RB30 swap in my S14 here in the States. I have been researching the conrod issue and I have a few questions for everyone here. I feel that I have beat myself up researching this and I just want all of your opinions since real world experiences are more important to me than the different companies marketing techniques. I am looking for around 800 AWHP, give or take a few HP.

I have narrowed it down to a few decent choices, knowingly staying away from the Chinese copies such as Manley, Spool (which appear to be ok) etc. So I have found the following, in no absolute order.

1) Pauter X-Beam Rods

2) NITTO I-Beam Rods

3) Argo I-Beam Rods

I know that all of these choices have the +'s and -'s, but I need your help with this. The Pauters come available (for an extra $45.00 a rod) with wrist pin oiling internally through the rod. The NITTOs supposedly have a jet near the main that squirts oil to the bottom of the piston, mimicing a block oil squirter. And the Argos speak for themselves with the RIPS boys.

So with cost set aside (since the rods are an important part of a longer stroke engine with higher RPM ranges) what rods do you recommend? No TItanium recommendations please, I don't have $6000+ for only rods.

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/403853-rb26rb30-conrod-choices/
Share on other sites

argo carrillo spool etc all decent rods, but i wouldnt put them in an rb30,

rb30 doesnt have block mounted oil squirters,

the oil squirter makes sure the oil reaches the bottom of the piston, which keeps it cooler, less detonation, less f**king around taking the timing out to loose power to prevent it detonating

without the oil squirter in the rod it will seep out towards the radius/ counterweights and will spray but will randomly touch the bore and bottom of piston skirt

rb30 STD & Nitto rods have oil squirters in the big ends of rods - thus the reason i only recommend the standard with up graded ARP bolts or Nitto H beam or I beam rods

(if you or anyone else knows of any other brands that have the oil squirter in the rb30 big ends then please post them up)

Alot of them have the notch on the conrod side faces to direct the spraying oil up the bore and onto the piston/small end area. But then again alot of engines dont have oil squirters and dont have issues. No doubt a buttload of rb30's running around without oil squirters and dont have det issues either.

H beams have the "valley" to guide the oil, but how does the oil get there?

The notches your talking of are on the sides right?

And im not talking about detonation consistently, my car plain H beams, tuned, bad batch of fuel detonated, rebuilt, coated pistons drilled 1.5mm hole in rod in line with bearing, tuner said he had more timing to play with, more chance of a better result

Yeh the conrod side faces. Same trick used by honda f1 back in the turbo era.

Argo I beam rods have the notches in the sides to direct oil up towards the bore.

Im not disputing what you are saying. Just saying there are alot of people with no oil squirters who dont even realise the difference, and there are people who do and dont realise the difference. Maybe in your NA engine it is more pronounced.

  • 2 weeks later...

Ive used spool rods in several 700hp+ rb30s with no problems.

They now have oils squirters also.

Good to hear........I was looking at their kits and what you get for $2K is pretty good value esp. for a streeter.

  • 1 month later...

Does anyone else have exp with spool? Ive heard some very positive results, but alot of negative also... generally with negative comments its always the 'cheap chinese imposter' with no foundation or reason for the remarks

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...