Jump to content
SAU Community

Recommended Posts

Ok so my 32 has a little issue,

This happens In the morning or the evening after the car has sat for a decent amount of time, I don't run the car hard as it is a daily, 45 min drive to work.

Anyway, I get smoke out of the exhaust, it seems to be an oil smoke.

It comes out when I accellarate, but only once....I.e

Accellarate to 3000 rpm, will smoke ...do it again to 3 k...no smoke

Rev further to higher rpm and more smoke after 3krpm, make sense?

It seems to clear it out, like clearing your throat.

I always warm the car up never drive cold.

My thoughts were theirs oil draining/ seeping somewhere it shouldn't and being sucked back into the engine when I go again later on.

One it's cleared theirs no more smoke

What should I be checking here?

I do know from a service report that my turbo oil drain line had a slight weep, any link here do you think?

Edited by GH05T
Link to comment
https://www.sau.com.au/forums/topic/406304-smoke-in-the-morning/
Share on other sites

Possibly valve stem seals. Car sits and a small amount of oil weeps past the seal. Start car, give it a squirt and the oil burns off.

Give it a comp test and if it comes up chipper, then it's likely the valve stem seals as they won't generally, affect your compression. If comp is down then you have a bigger problem.

Then I'd say almost defo valve stem seals.

If it is valve stem seals I wouldn't be too concerned. Just make sure you keep an eye on your oil level and if it gets worse, like blowing smoke under power and or a lot of of smoke on start up, then it's time to look at getting your head refreshed.

That puff of smoke on cold takeoff is usually condensate oil from the PCV running down into the manifold overnight. You can try fitting a small sealed catch can full of stainless steel wool in the pcv hose to prove it.

That's what it seems like, from a stand still any acceleration gives a noticeable amount of blue smoke (visage at night in headlights behind) and like I said its like it puffs as far as it revs, but only once, accel to 2000rp with smoke but only once, more smoke when you go past that rpm again,

Is this problem going to get worse if the car gets driven hard? I drive daily and maby one in a while it gets a caining, should I be carefull, is their anything I can spenda bit of coin n to help further expenses ?

I always warm the car up never drive cold.

Drive it cold (but sensibly!). Most of the damage is done when the engine is cold. It will warm up much quicker than simply letting it idle.

And you won't be coming back later asking why your fuel economy is so crap.

dont care at all about fuel i dont pay for it, i run my car for 15 mins in the morning before driving, i run it for about 3-5 in the evening after work, nether affect the smoke though, its always the same

Blind_elk is right. Warming up vehicles, especially ones that rev, is a very bad idea. Generally at idle the oil pump isn't pushing a great deal of oil around and there's not much temp increase which means it takes longer to get oil everywhere and also up to temp.

Start car, let idle for 30 seconds then get driving.

Idling a cold car for 15 minutes is a great way to destroy rings and valve stem seals.

Yeah idling for 15 minutes is not a good idea at all, would barely warm it up, would get up to temp in 1-2 minutes of normal driving otherwise. Start it, wait 30 seconds then drive off staying off boost until temp is up.

Smoke could be turbo seal or valve stem seals.

Edited by Rolls

Valve stem seals means head off. In reality leaky valve stem seals won't do any damage (at least in your case as it seems not too bad.. They'll just progressively get worse until such time as it smokes a lot more or all the time and then it needs to be fixed.

I'm not sure how hard it is to get the head off an RB as I've not done one, but once off, barring any weird RB specific oddity, the seals might be maybe $100 or so and the work to actually fit them might be 4 hours (that's a pretty rough guesstimate). Of course, if it were me, with the head off and the valve train off it would be hard to resist giving the head a through going over.

As for turbo seals, that's a tougher one. That means turbo off and either a "back to stock" rebuild for $500+ or replace with something tastier for $1000+ plus required supporting mods.

TBH it sounds to me more like valve stem seals rather than turbo. I think if it was the turbo it would produce more smoke under load.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...