Jump to content
SAU Community

Disposing Used Coolant

xntrq

By xntrq,
in General Automotive Discussion

 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Damn, i thought the newer generation of coolants were environmentally friendly(er) n putting them down the drain wasnt a problem.

Not so the case?

I asked the local Natrad bloke what he does with his waste, he said he treats it (to even out the PH I think) and then dumps it down the drain.

GTR-N1 Grand Master

GTR-N1

Posted
Posted

I asked the local Natrad bloke what he does with his waste, he said he treats it (to even out the PH I think) and then dumps it down the drain.

There are many neutral pH substances that should never be dumped in a drain.

The treatments he uses might include (amongst other things) surfactants as well as acid/alkali chemicals I think

*LOACH* Veteran

*LOACH*

Posted
Posted

just tip it on your weeds....

don't pour it down the drain and do not tip it on your weed...

I just chuck it on the plants...doesn't seem to do them any harm, in fact I noticed that at my parents house the weeds that my father emptied coolant on did better than the neglected adjacent weeds which didn't get a watering.

gotRICE? Veteran

gotRICE?

Posted
Posted (edited)

Lol seems like my "pouring down the toilet" post got deleted.

The only reason i said that is because all sewerage in the City i lived in is processed in a treatment plant before going anywhere near the ocean. The water outlet from it is cleaner than the water its being dumped into. So really its not a bad option. :)

And im pretty sure a treatment plant is well equipped to handle anything that could possibly be flushed down a toilet. They would have had it all and some.

Edited by gotRICE?
sydking Veteran

sydking

Posted
Posted (edited)

If some of you have seen what ends up in the tips, and leaches into the ground, Coolent it the least of your worries - Though im not one to add to the crap land fill.

Check with local council - i know mine has cirtain days per year were they set up a big chemical/paint/oil waste disposal at a local carpark,

They let you bring it all and dispose of it, Best thing it, due to saftey they wont let you out of the car, So pop your boot and they will grab it all out for you :)

Actaully my local council has some good services- Free woodchipping/mulching 5 times per year its great. Free mulch and dont have to take anything to the tip, Just go nuts with the chainsaw and leave it all out the front drive way- Come home to 6-7 bags full of fresh mulch.

Edited by sydking
sydking Veteran

sydking

Posted
Posted

Lol seems like my "pouring down the toilet" post got deleted.

The only reason i said that is because all sewerage in the City i lived in is processed in a treatment plant before going anywhere near the ocean. The water outlet from it is cleaner than the water its being dumped into. So really its not a bad option. :)

And im pretty sure a treatment plant is well equipped to handle anything that could possibly be flushed down a toilet. They would have had it all and some.

Thats cool!, Our here in sydney goes straight out intot he ocean, Feild of mars even has the old above ground sewage tunnles from many years ago.

And wasent it maroobra beach back in the day that had the sewage pipes leading straight into the beach haha

jjman Mentor

jjman

Posted
Posted

Lol seems like my "pouring down the toilet" post got deleted.

The only reason i said that is because all sewerage in the City i lived in is processed in a treatment plant before going anywhere near the ocean. The water outlet from it is cleaner than the water its being dumped into. So really its not a bad option. :)

And im pretty sure a treatment plant is well equipped to handle anything that could possibly be flushed down a toilet. They would have had it all and some.

whilte the sewerage processing systems can deal with it, doesnt mean that it easily or prefereably can. For example, the amount of processing that it takes to sort bleach via the sewerage system is huge. But of course most people do use bleach in their toilets n sinks. But, essentially, its bad for the sewerage processing system.

Im sure coolant would also fall into this category.

xntrq Veteran

xntrq

Posted
  • Author
Posted

OK, I've just asked my neighbour Ricky, who has a 80 year old Antique car.

He (Alan) will gladly take that pre-1985 coolant off your hands :)

I can pick it up for him.

Sure man, but its a little bit of a drive to pick up for a bottle of coolant!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...