Jump to content
SAU Community

Recommended Posts

It's new merchandise time!

We would like to offer all SAU VIC members the opportunity to order a simple SAU VIC logo jacket.

Jacket #1 is the winner!

$75 + post, Fleasy on the inside and warm, water resistant, pockets inside and out.

SAU VIC logo on the front, www.sauvic.com.au in small font down the bottom on the back.

Jacket 1

Red piping, thicker weight, shinny outside

post-59171-0-54945600-1345075306_thumb.jpg

So which one do people want? We need a minimum of 30 units to make an order, we will not be stocking these and they will be order only in groups of min 30!

Once 30 has been reach we will wait 14 days before placing the order to allow for anyone else wanting these.

This is SAU VIC members only.

http://www.sauvic.com.au/how-to-join

Payments can be made to:

Bank Deposit Details

Name: Skylines Australia – Victoria

Bank: Westpac

BSB: 033305

Account Number: 265609

Reference: J1 forumname

$75 + $10 post. You can pickup for Garage Cafe meet for free.

These are jackets, so if you want it more fitting drop back a size.

Also, if you want it posted. Please email [email protected] with your mailing address.

Jacket 1

post-59171-0-49690400-1349384764_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/407120-jackets-taking-orders/
Share on other sites

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey Marco just want to double check if your an SAU VIC member?

Edit: Just saw your application. Welcome aboard :D

hey tony just wanted to double check that your asian?

Edit: just saw your eyes. watch out for the board. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...