Jump to content
SAU Community

Recommended Posts

Hey Guys

Car: 1997 R33 S2 GTST

Tyres : 265's x9 rear and 235 x 8.5 front and decent tyres as well

Suspension : Pedders Coilovers

Ok so im under no impression that im a great driver by any means but now I spin out ALOT.

I span two weeks ago ( a full 180degree spin) when going around the roundabout in the wet. I went around it quite slowly(factoring in that it was wet and in driving a rwd car) but I still span out. It took me by surprise as I was being cautious and didnt expect this so I span without correcting . Was doing about 40km/h.... first thought was I hydroplaned....

Yesterday it was pouring again , remembering my last experience I went even slower this time , but wasnt taking a right like before and was going straight through the roundabout , so a slight turn of the steering wheel was all that was needed. I was doing about 35km/h. Without warning after i turned , the back end slipped out,this time i was more prepared....so i corrected but my god that took me by surprise.

I dont feel i have the skills to get myself out of trouble should this happen again with traffic around....

What would be cause this to happen? Coil overs? My missus car can go straight through a roundabout in the rain doing 40km and not spin out....why is the line so shit in rainy weather....to the point of being dangerous

This has only started happening since i got coilovers(which virtually eliminated body roll)...im quite sure that the act that I have a much lower center of gravity has something to do with it but how exactly... whats the physics behind this? I assumed having no body roll was a good thing , but now in the wet I have to take corners slower!

And what can I do to avoid slipping out in the wet all the dam time - already have fat 265's in the rear

Cheers

Link to comment
https://www.sau.com.au/forums/topic/407716-so-i-spun-out-again-wtf-is-going-on/
Share on other sites

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

Hey Guys

Car: 1997 R33 S2 GTST

Tyres : 265's x9 rear and 235 x 8.5 front and decent tyres as well

Suspension : Pedders Coilovers

This has only started happening since i got coilovers...

Cheers

This must be totally unnerving for you whilst you have a car that would predictably corner much better than most.

Obviously you had Pedders supply and fit these coilovers?

Did they tighten everything up?

Have you had your wheels realigned by them too?

Did they do a complimentary multipoint check?

It sounds like there's basically no weight transfer at all in your set up.

If your springs & shocks are too stiff; you'll get no warning when it's about to break away.

No body roll is not necessarily a recipe for good handling; there has to be some compliance; otherwise the car won't absorb any bumps, it just bounces over them.

No wheel on the ground; no traction from that wheel. Doesn't matter how wide your tyres are then.

Do the coilovers have adjustable damping? What are the spring rates?

I'm better you have poor tyres combined with suspension too hard makes for a difficult life.

I could drive my GTS-R in pissing rain, with 245/255s on the rear and 370rwkw - not having an issue at all with spinning out. The suspension was as hard as a rock with virtually no movement in it at all (12/10kg springs). Difference was I was spending $300 a tyre.

My money is on shit tyres. What are they?

Pedders coilovers arent harder than some jap spec ones. So Im declined to blame that.

My mates 32 had a problem with spinning around spontaneously, but his hicas light was intermittently on. So we blamed that.

But for you, Get some better tyres. Or go and do a defensive driving course, as you will hurt yourself or worse others. You need to learn to drive that thing.

Do you accelerate out of the roundabout when this spin around occurs?

When you think about it, 40km/h is bloody fast on a tight roundabout.

Skinny tyres are far better in the wet. Wide, cheap, worn tyres in the wet will grip as much as a bucket of eels in whale snot.

Wouldn't be suprised if someone has taken the swaybars off the car.

Also, get under the car and have a look at the chassis rails and make sure theyre nice and straight.

maybe who ever did that threw them over a Nissan Dealer

My liner was shit in the wet, used to slide stupidly without wanting to but nothing some counter steer wont fix,

changed to Federal 595RSR's and its been sticking very well im comfortable enough in the wet to

give it some where i wouldn't have before.

Wouldn't be suprised if someone has taken the swaybars off the car.

Also, get under the car and have a look at the chassis rails and make sure theyre nice and straight.

Taking the swaybars off will actually let the car float around a little more.

I know a few GT-R owners who will drop/loosen the front swaybar if it's really wet at a track day to get more weight moving :thumbsup:

Front and rear strut brace and sway bars make a huge difference and some great set of tyres.

These stiffen the car up, especially with stiffer/upgraded rear sway bar, which tends to reduce under steer thus promoting over steer.

90% of it sounds like your skill as a driver. Skylines are tail happy cars, poor tyres, wide tyres, and stiff suspension definitely won't help. But they're just tail happy by design.

Tips: Corner as smooth as you can, don't jerk the steering wheel (I'm sure you're not JERKING it per say, but just try and be more smooth); and practice smooth throttle control. It'll still be a little difficult to control as stated above they're just a tail happy car. But in the wet you simply just have to have to drive like a grandma. Smooth throttle, smooth steering and you'll be fine.

There also becomes a point where wide tyres don't help you in the wet, I'm not sure of the exact threshold... but yeah there becomes a point where it's actually detrimental for grip in the wet.

edit: Or just buy an AWD car. :D

Edited by RB25PWR

But in the wet you simply just have to have to drive like a grandma. Smooth throttle, smooth steering and you'll be fine.

Or just buy an AWD car. :D

This.

I went from driving a WRX to a Skyline and knew nothing of the oversteer.

After you realise how little throttle you need to get all Tokyo Drift, you adjust your driving style.

So in conclusion.

EN1cT.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...