Jump to content
SAU Community

Recommended Posts

Silicone hose plus OEM type spring hose clamps work fine on anything that has a barb or flare on the end of it. If you're trying to put the hose onto a pipe with no barb/flare, silicone may well creep off, especially with boost.

I have successfully made a flare on the end of such pipes before by using a little epoxy putty to build up the outside of the pipe tip.

Link to comment
https://www.sau.com.au/forums/topic/416064-vacuum-hose/#findComment-6678694
Share on other sites

Each to their own Anthony, no-one bagged you out for buying an overpriced Stagea... Did they...

Turbosmart makes some of the best silicone Vacuum hose I have found, the Autobarn stuff kept splitting on me. Definitely cable tie the ends, should be good for over 50psi as tested by myself.

Link to comment
https://www.sau.com.au/forums/topic/416064-vacuum-hose/#findComment-6681970
Share on other sites

It just can't handle the heat. I have replaced all my stock hoses due to leaks as they had all gone hard. After a few years, the replacement hoses have all gone hard and are leaking again. Silicone doesn't have that problem.

Why don't we use rubber on our aftermarket intercooler piping joins? Because we have all seen the factory rubber go hard causing leaks. Reinforced Silicone ftw.

Link to comment
https://www.sau.com.au/forums/topic/416064-vacuum-hose/#findComment-6683020
Share on other sites

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...