Jump to content
SAU Community

Recommended Posts

I've been told that all cars, in particular Japanese cars, overestimate your speed, so that the speed shown on your speedometer is actually off by a bit. I tested mine using a phone app called Ulysses Speedometer which uses GPS tracking to measure your speed exactly. I discovered that my speedometer is off by a ridiculously huge 8.3%. Which means when my speedo reads 100, I am actually only driving 91.7. And that to reach 110kmph which is the top speed on some highways, my speedo actually has to read 120kmph. I dislike having to estimate the speed I am driving at and never quite sure if I am now speeding or not, and am annoyed that I must be the frustrating person on the road driving unecessarily under the limit.

Have you guys measured the difference on your car? Is it similar to mine? Can it be adjusted?

Edited by puddlejumper

my old car had speed on the turbo timer which was usually about 2 kph less than the speedo at about 100km. the timer was calibrated at 60kph from the speedo though...

Comparing speedo to satnav in other cars usually had about 2-3k difference also (but they weren't jap)

So i think usually a speedo is only a cpl k over actual speed.. things such as tire size and wear can have an affect on the precise accuracy...

As per above, unless you are running the stock tyre sizes (which almost no-one ever does - even on stockies), then you will affect your speedo's accuracy. My tyre width/profile is WAY off - my speedo is out by about 15%, but I compensate for it and normally use my GPS digital speedo instead of the oem cluster.

You will find all the V35's and M35 Stageas have this discrepancy, but the ecu gets a good speed signal and you can display this actual speed via the obd2 port. (it is much more accurate.)

I agree, it is very annoying and can cause frustration, 10k's out at 100 is a joke.

My V35 is fairly close. About 2% last time I checked with GPS. And I am running stock size tyres.

But our J31 maxima is out by about 8%. Again with stock size tyres.

My V35 Coupe seems to almost spot on - I've tested at 80 & 110 against the GPS in my phone, and the difference is no more than 1 - 2 kph. I've got 18s with stock rear tyres - 245/45R18.

I got 2km/h difference between the fronts and rears because of the tire sizes (width and profile) that came with the wheels, I'm not sure how much it is in relation to the speedometer. Use this tire size calculator (http://www.1010tires...ecalculator.asp) to help you choose the tires within the closest possible tolerances for your set of wheels. There may be other factors as well...

Edited by 81gSKy

Here's the results of a test I did a while ago. As per above, the Informeter (display from OBD2 data) is accurate, thus confirming Nissan deliberately engineered our cars to show the incorrect speed on the dash.

post-76144-0-12092300-1356565897_thumb.jpg

So, are we saying that the GPS is connected to the engine control (ie fuel)? and the traction control as well? What happens when the GPS loses a signal?

So, are we saying that the GPS is connected to the engine control (ie fuel)? and the traction control as well? What happens when the GPS loses a signal?

?? GPS is only used for Navi. If you don't have Navi, your car doesn't even have a GPS receiver. the ECU uses wheel speed sensors to determine vehicle speed (as well as using them for ABS, TC and VDC). If you are running stock size tyres, the ECU speed derived from these sensors is quite accurite.. however, the speedo doesn't display exactly what the ECU reads, the speedo almost always reads faster.

If you look at the graph above you will see it isn't 10% across the board.

I corrected the speedo on my J30 years ago, there was an adjustment on the back of the speedo cluster which adjusted a % of speed, however, the speedo was also out by an absolute figure, there was no adjustment for this, but fortunatly I was able to elongate the mounting holes where the speedo mechanism attached to the face, that allowed me to make an absolute adjustment and I was able to get the speedo to read accurite at 60, 80 and 100km/h.

I had a look at the back of the speedo cluster on the J31 Maxima, but there is no physical adjustment.

  • 2 weeks later...

at least puddles speedo is out in the negative direction. years ago i found out the hard way that my car was showing 100 on the speedo but was actually doing 111 on the road... *flash*

at least puddles speedo is out in the negative direction. years ago i found out the hard way that my car was showing 100 on the speedo but was actually doing 111 on the road... *flash*

You should've been able to contest that... Right?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...