Jump to content
SAU Community

Recommended Posts

to get the r31 started, i took the battery out of my s14. without thinking, i just connected up the leads.

thus putting them on the wrong way. switched them around, all good. the car started.

however, non of the electrical features now work. lights, interior stuff, dash. ect.

i have already checked the in cabin fuses but they are fine.

i know very little about r31s, i can't seem to fine any other fuse boxes.

what do you guys think i broke?

Link to comment
https://www.sau.com.au/forums/topic/416178-battery-on-the-wrong-way/
Share on other sites

to get the r31 started, i took the battery out of my s14. without thinking, i just connected up the leads.

thus putting them on the wrong way. switched them around, all good. the car started.

however, non of the electrical features now work. lights, interior stuff, dash. ect.

i have already checked the in cabin fuses but they are fine.

i know very little about r31s, i can't seem to fine any other fuse boxes.

what do you guys think i broke?

Oh no

Mate you could have killed off half the car !!

the car is neg ground not positive so anything with a relay or fuse , fuse link or diode ( alternator) could be smoked

your going to have to go thru one thing at a time and check the lights too

Your damn lucky if the ecu doesn't have a fried trace or two it would be a miracle of Christmas

Best of luck

I remember when i was about 12 my dad thought he would play mechanic and put a new battery in his old el wagon, nek minnit put it on the wrong way and fried the ecu, 700 dollars later mother wasn't impressed :P

A 12 year old should never take the opportunity (behind Dad's back - but still within earshot), to ask Mum if he can go over to his mate's place when there are chores to be done; that Dad told him to do.

Dads can only 'single-task'!!! :mad:

R31's have a fusible link and relay box behind the RH headlight. You may have fried a fusible link, maybe. But i doubt it.

The other fuse box is inside, RH side of the steering column. This is more than just a fuse box though. This is called the HEC or Hybrid Electronic Control unit. Its also considered to be the SMJ or Super Multiple Junction. Only R31's had them and they are not the most awesome of things. But they dont usually fail either.

This unit has a few purposes; its a place for all the fuses and power relays (can't see the relays without removing the unit), it is the major intersection for everything electrical in the car, and it also houses the electronic control module that controls; dash lights, tail lights, wiper control, interior light, trip computer etc. I dare say you have fried this unit.

If you've still got brake lights and head lights but not much else then its a good indication that its cooked.

You can replace just the electronic module or the entire HEC. Should only take half an hour to replace the entire HEC. Grab one from pick a part.

R31's have a fusible link and relay box behind the RH headlight. You may have fried a fusible link, maybe. But i doubt it.

The other fuse box is inside, RH side of the steering column. This is more than just a fuse box though. This is called the HEC or Hybrid Electronic Control unit. Its also considered to be the SMJ or Super Multiple Junction. Only R31's had them and they are not the most awesome of things. But they dont usually fail either.

This unit has a few purposes; its a place for all the fuses and power relays (can't see the relays without removing the unit), it is the major intersection for everything electrical in the car, and it also houses the electronic control module that controls; dash lights, tail lights, wiper control, interior light, trip computer etc. I dare say you have fried this unit.

If you've still got brake lights and head lights but not much else then its a good indication that its cooked.

You can replace just the electronic module or the entire HEC. Should only take half an hour to replace the entire HEC. Grab one from pick a part.

ill check it out however, nothing works including brake/head lights.

Lights should still work if they are direct fed from a battery source. They are not polarity dependant. So if there not working they must be fed from a Control Module that could be fried.

You might have to get a multi meter out and start checking where the 12v goes into and where there should be an output.

You might need a wiring diagram.

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...