Jump to content
SAU Community

Recommended Posts

When i fill through the shifter hole, take out the plug on the side that is meant for filling it and just pour in through the shifter hole and get a mate to tell you when it starts coming out of the side hole, then its full.

Yea, i meant powder coating, i was overly tired last night, probably should have posted that today. Any places that you guys would recommend?

Marshall Powder Coaters in Wingfield did my covers... cheap as too

-D

Easy. Jack up car, undo plug on the bottom of the gearbox, drain, replace plug, and top up either through the plug on the side of the box (hand pump is very helpful in this instance) or through the shifter hole (with the shifter removed).

If filling through the plug on the side, stop filling when the fluid starts coming out (obvious).

If filling through the shifter hole, just add the prescribed amount of fluid (I can't tell you how much).

When i fill through the shifter hole, take out the plug on the side that is meant for filling it and just pour in through the shifter hole and get a mate to tell you when it starts coming out of the side hole, then its full.

Thanks again guys

Marshall Powder Coaters in Wingfield did my covers... cheap as too

-D

Seconded.

Or Art Metal Coatings in Holden Hill.

Avoid the place on Main North near Gepps cross like the plague.

That's kinda the look they were going for...

Interior is basically Cruze bits anyways (steering wheel, dash cluster etc etc)

The Holden owning fraternity will be up in arms.........the final model Commodore (going by predictions) and they FINALLY put the window controls in the armrest in the door

Interior is basically Cruze bits anyways (steering wheel, dash cluster etc etc)

The Holden owning fraternity will be up in arms.........the final model Commodore (going by predictions) and they FINALLY put the window controls in the armrest in the door

They also moved the boot release onto the drivers side. No idea why they had it in the glove box.

They also moved the boot release onto the drivers side. No idea why they had it in the glove box.

back in the VK VL days, thats how the passenger got out...

Edited by Deep Dish V35
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...