Jump to content
SAU Community

Recommended Posts

Whilst correct there Hanaldo, as Ali pointed out, it's extremely difficult to prove what has been said in a verbal contract...which is why so many cases built around them get chucked out.

We used to have a saying where I used to work; because we dealt with a lot of legalities, terms and conditions, people threatening to sue etc. it goes: "Put it in writing."

Oh and never sign for registered mail that comes in an envelope ;)

Fark that's a good deal, would have been very keen if it wasn't sold.

Going by OP's history...it's far from sold. Make an offer.

Fluttershy stop trying to poison this topic with pathetic little comments. Car is sold unless buyer pulls out at this stage. Thanks

you acknowledged its existence.

get ready.

Whilst correct there Hanaldo, as Ali pointed out, it's extremely difficult to prove what has been said in a verbal contract...which is why so many cases built around them get chucked out.

We used to have a saying where I used to work; because we dealt with a lot of legalities, terms and conditions, people threatening to sue etc. it goes: "Put it in writing."

Oh and never sign for registered mail that comes in an envelope ;)

Going by OP's history...it's far from sold. Make an offer.

You can be legally served with only attempts now, if you have served the last known address, even without the person I'm question being in attendance, they are still considered served.

I do it all the Time now at work lol

Vu,

Does the R34 have factory panel gaps?

Wouldnt mind some pics of the rolling shell for a panel gap inspection...

All original paint and panels? What is the underbody like and any rust etc?

I will give you 35k cash! Lol

My two cents and I have done thus many many times in business once you give your word that's the end of it. The car was clearly sold in both of their minds but in the end it falls on integrity of seller. Another example say if something is marked incorrectly at my shop and there's been a price rise or its even below cost I feel I must sell it at the marked price, sucks for me but my integrity is important too me . This post has gotten very personal though which is a shame.

Scott

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
    • Got my 34 gtt tuned last week. Car made 362 wheel horsepower at 19 psi. Turbo was the ATR43SS. Only other upgrades were haltech 2000 series. 650cc injectors, walbro 250, fmic. Pro hub dyno reads 6% lower than actual figure according to my tuner. Car is a real ripper now.  IMG_7261.mov
    • Hi everyone, I'm wondering if anyone in Melbourne (preferably West) has a non-S2 R34 front bar. If it's already off the car, even better!  Nothing too weird, I just need to get a cut-out of the hole that the front indicators clip into 🤣 (image attached for reference)   I've got a front bar from JSAI Aero, but those holes need to be cut myself, and I want to get it right so the indicators will clip securely. And my OEM bumper is a S2, so I have no reference. So looking for a member who might be able to spare me a few minutes to make a cardboard cut-out using your front bar.
×
×
  • Create New...