Jump to content
SAU Community

Recommended Posts

FYI All.

Penrite have been working with Import Monster to co-sponsor this event with some prizes!!!

That's right, this DECA we will have prizes for the top 3 competitors in the way of a pack of Penrite 10Tenths Racing Products valued at $200 each.

Penrite will also have a stand at this event to answer any product related questions you may have :)

Penrite-logo-1.jpg

  • Like 1

Yeah because the only way RWDs can do well is to use R spec tyres...cheats! Sif run $2000++ on tyres for entry level motorsport. What a joke. RWDs and their drivers are a joke.

nothing like a $500 motor beating a $15,000 motor :yes:

nothing like a $500 motor beating a $15,000 motor :yes:

hehe..

Yeah because the only way RWDs can do well is to use R spec tyres...cheats! Sif run $2000++ on tyres for entry level motorsport. What a joke. RWDs and their drivers are a joke.

They're not worth $2000++ anymore haha.

So hang on...Inferior breed? You mean r33? You have r33 engine, r33 gearbox, r33 lower control arms, r33 clutch master cylinder, r33 rear end, or r32 GTR? The front bar, front guards, the grille or the bonnet? I'm confused lol.

So hang on...Inferior breed? You mean r33? You have r33 engine, r33 gearbox, r33 lower control arms, r33 clutch master cylinder, r33 rear end, or r32 GTR? The front bar, front guards, the grille or the bonnet? I'm confused lol.

R32.75? :woot:

So hang on...Inferior breed? You mean r33? You have r33 engine, r33 gearbox, r33 lower control arms, r33 clutch master cylinder, r33 rear end, or r32 GTR? The front bar, front guards, the grille or the bonnet? I'm confused lol.

It's what's in the heart that counts. It's like moving Leon from Packenham to Toorak. He'd still be known as Leon from Packy.

  • Like 1
Guest
This topic is now closed to further replies.



  • Latest Posts

    • There are black hose clamps as well if you care. Plazmaman for example sells some: https://plazmaman.com/product/black-hose-clamps-premium-quality-stainless-breeze/
    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
×
×
  • Create New...