Jump to content
SAU Community

R34 Gtt Fault Code 33 - How To Clear Heated Oxygen Sensor

neopowered34

By neopowered34,
in General Maintenance

 Share

Recommended Posts

neopowered34 Collaborator

neopowered34

Posted
Posted (edited)

Hey Guys

Got sick of my engine light being on this week so I did the self-diagnostic test as seen on this website and it flashed the code 33 which apparently means heated oxygen sensor. I just had installed a KLS split dump pipe (with the correct thread for the sensor) and now it wont turn off

Anyone had this problem before or know how I could go about rectifying it?

Geoff

Edited by neopowered34
neopowered34 Collaborator

neopowered34

Posted
  • Author
Posted (edited)

So I played round with the connections as the exhaust shop left one half clipped and the light has gone off after a good drive, fingers crossed it stays off!

Edited by neopowered34
RB25DETC33 Community Regular

RB25DETC33

Posted
Posted

So I played round with the connections as the exhaust shop left one half clipped and the light has gone off after a good drive, fingers crossed it stays off!

Check the fault code again. Although the light isnt on it may still be faulty. My 34 has the code 33 at the moment, my 02 sensor is shagged but the light doesnt always come on.

  • 2 months later...
Chris32 Veteran

Chris32

Posted
Posted

Mine threw up this code yesterday, it came on after a bit of a spirited drive. It went away for around 30 mins but came on this morning on the way into work.

Definatley a dud sensor then, or does it just overheat when on boost and then come good? My car too has a split dump pipe

neopowered34 Collaborator

neopowered34

Posted
  • Author
Posted

Mine threw up this code yesterday, it came on after a bit of a spirited drive. It went away for around 30 mins but came on this morning on the way into work.

Definatley a dud sensor then, or does it just overheat when on boost and then come good? My car too has a split dump pipe

Mine ended up staying off so was the connection that the exhaust shop left off. Just double check them and if your sensor is dud move it off for a new one :)

Chris32 Veteran

Chris32

Posted
Posted

Yeah I unplugged it and gave it a quick spray with rp7, been good since.

Checked the air fuel ratio on the dyno and it was a constant 13.7/1 at cruising speed/throttle

Ben C34 Grand Master

Ben C34

Posted
Posted

Yeah I unplugged it and gave it a quick spray with rp7, been good since.

Checked the air fuel ratio on the dyno and it was a constant 13.7/1 at cruising speed/throttle

is that a typo? Should be 14.7

Chris32 Veteran

Chris32

Posted
Posted

is that a typo? Should be 14.7

Nah, defiantley was between 13.2 - 13.7 under reasonably light load / light acceleration up to crusing speed.

I woulddn't have thought you'd acheive perfect stoich mixture, even at idle?

Anyhow, car was on the dyno making sure the Nistune I put in was functioning right, and it was only the WOT settings that ended up being tweaked to suit. We'll be looking at the light load stuff when I've got a bit more time.

So far though, I'm getting better economy than the stock ECU which means its all going in the right direction

  • 2 months later...
B-rice Mentor

B-rice

Posted
Posted

Just wondering where everyone is getting their OEM sensors from. Im changing my dump and trying to avoid using the FORD EL. Ive found this on ebay

http://www.ebay.com.au/itm/Nissan-Skyline-R34-RB25DET-3-wire-exhaust-oxygen-sensor-O2-EGO-lambda-/161066223512?pt=AU_Car_Parts_Accessories&hash=item25804b8798&_uhb=1

http://www.ebay.com.au/itm/NEW-Universal-3-Wire-O2-Oxygen-Sensor-suits-Nissan-Skyline-R34-Neo-RB25DET-/111128785790?pt=AU_Car_Parts_Accessories&hash=item19dfcab37e&_uhb=1

Got a Pulsar Grand Master

Got a Pulsar

Posted
Posted

Hey Bryce, Jeremy just got one from Ebay which I installed for him. Seems to have stopped his Engine light coming on.

It was a PEC brand which is what his old one was too. You just need to connect it to the stock Plug.

Vulture Motorsport sells them on here. :thumbsup:

Edit* Linkages ---->> http://www.ebay.com....#ht_3034wt_1245

---->> http://www.skylinesa...n-sensor-59-ph/

  • 4 weeks later...
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Josh, sorry for the noob question, understand that there are 2 oxygen sensors on the RB25DET? Kudos only sells 1 kind, does it fit for both? I too have a fault code 33. Cheers!

there's only one, the other sensor is a cat overheat sensor for the dash

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

Oh, thanks very much Johnny, I was informed by my mechanic that there were 2 different sensors. Any idea if it's easy to DIY? Cheers!

Yes mate, very easy to do. Al you need is (from memory) a 21mm spanner. Unbolt old sensor, bolt in new sensor. It is located behind the turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      RH9 R32 GTR Build Thread

      By soviet_merlin · Posted

      Out of curiosity, how do you cover up the inspection hole? Surely it doesn't sit open like that, right? With grime and dirt coming in and oil going out?
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Hi from Canada, Both of my calipers are starting to fail. My car is a 2005 M35 Stagea ARX and I can't seem to find any parts or any cross reference caliper that would fit my car. Is there a company or a similar caliper that would fit and I could replace the OEM one. Or if anyone knows where I can find a new OEM. Any help is very appreciated. Let me know!
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • Matt Z
      SAU NSW - Bathurst Run 2025

      By Matt Z · Posted

      🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...