Jump to content
SAU Community

Recommended Posts

Got a bit more done, pulled the motor and gearbox out of the rusty yellow shell to start fitting the sub frame adaptor plates into the hatch.

Pauls, I want to get full rego to show what can be done under NCOP, the club rego is the last resort but even with the vic club rego the inspection is

still done by a VASS engineer. It's surprising how many skyline owners have a soft spot for toranas and on the gmh-torana site a lot of torana owners

have a soft spot for skylines. I suppose physically they are both about the same sized car and both are Bathursh winners.

IMGP2311_resize_zpsd7c2b59b.jpg

A lot of people were heralding NCOP as the end of the modification world. I truly hope to see this project of yours go through with engineering approval to get full rego to show that if the quality of work and engineering practice is good, you can still have your toys. Your attention to detail and quality of work has my respect.

  • Like 1

Nice work! i've been lucky enough to have a father who was a spray painter,over the years i have watched him do up 13 toranas of his own and im just as excited to see yours finished as i was his.Keep up the good work mate. :thumbsup:

Edited by gleeson

Got some more done, tacked in the rails and fitted crush tubes for the subfame adapter plates.

IMGP2320_resize_zps7fcc7d4f.jpg

Made 4 bosses to fit into the original torana subframe mounting holes. These are welded into the top and bottom of the rail to help tie it together and allow for another mounting point.

IMGP2312_resize_zps7b1b1466.jpg

IMGP2317_resize_zpsec5e09be.jpg

Started fitting the suspension towers.

IMGP2321_resize_zps07453574.jpg

IMGP2322_resize_zps932499dc.jpg

  • 3 weeks later...

Cut the tunnel out of the skyline, it made me a little sale to destroy such a nice car.

Also talked to the engineer about track width and tyre and rims sizes, found out rim size is now determined by taking the

widest tyre offered and increasing it but 30% then use the tyre fitment guide and see what rims suit that tyre.

Since i'm using the skyline suspension and sub frame I can use the skyline track width and tyre/wheel combination.

So R32 gtr had a 225/50r16 I can run up to a 285 on the front and the R33 had a 245/45r17 which works out to being up to a 315.

But I can only change the track width by 25mm.

IMGP2344_resize_zpsa40a01a0.jpg

Sat the skyline tunnel in the hatch.

IMGP2348_resize_zps544c7046.jpg

Extreme ATTESA pump removal.

IMGP2345_resize_zps57d78d0e.jpg

Ive been on sau for about 10yrs and ive never seen anything as unique or exciting as this build...thanks for sharing - u are using the 2 most appealing cars in my mind to create a work of art :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...