Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

Hey I plugged in my consult today and the o2 sensor plays around at .70 to .80 volts, is it busted, could that be why I'm only getting 200kms to a tank, if so where's the best place to get a brand new one, there's no point in getting a second hand, thanks.

im looking at replacing my 02 sensor that is attached to the dump pipe and i came across this one on ebay what are peoples thoughts on it link is pasted below

http://www.ebay.com.au/itm/NEW-Nissan-R33-Skyline-NX-NX-R-N14-N15-Pulsar-O2-Sensor-/150632217769?pt=AU_Car_Parts_Accessories&hash=item2312613ca9

  • 3 weeks later...

I bought an aftermarket one off kudos motorsports which plugs straight in (highly recommended trader)

Didn't really improve my fuel economy but i do 90% city driving. I wonder whether the geniune item which is double the price can do a better job...

I bought an aftermarket one off kudos motorsports which plugs straight in (highly recommended trader)

Didn't really improve my fuel economy but i do 90% city driving. I wonder whether the geniune item which is double the price can do a better job...

It either works or it doesn't there isn't much to them. If it is working then buying another working one will produce basically identical results.

  • 3 weeks later...

Fellas:

100% confirmed that NGK / NTK part no: OZA395-E2 can fit in an r34 GT-T and does work.

100% confirmed the plug DOESN'T FIT, however the switch is extremely simple.

im getting MUCH better fuel economy since installing the Zirconia 3-Wire, 22mm O2 sensor for the 32 / 33.

stop paying $220 for the original one!!!

Tim

  • 3 weeks later...

Installed Power FC - doing basic setup for a tune as suggested in the Power FC FAQ.

Whenever I put it into closed loop mode it starts to idle really rough, A/F goes very rich on my wideband (12:1), and it barely drives. If I take it out of closed loop it runs richer than standard ECU but idles and drives normally.

I know closed loop relies on the oxygen sensor to trim fuel at steady accelerator levels - so does the above indicate it is stuffed? I did a sensor check at idle through the hand coontroller and it sat at 1.3 V. i revved it and it didn't change? Is it time for a new one?

Thanks,

Pete

Installed Power FC - doing basic setup for a tune as suggested in the Power FC FAQ.

Whenever I put it into closed loop mode it starts to idle really rough, A/F goes very rich on my wideband (12:1), and it barely drives. If I take it out of closed loop it runs richer than standard ECU but idles and drives normally.

I know closed loop relies on the oxygen sensor to trim fuel at steady accelerator levels - so does the above indicate it is stuffed? I did a sensor check at idle through the hand coontroller and it sat at 1.3 V. i revved it and it didn't change? Is it time for a new one?

Thanks,

Pete

yes

you may also be able to run a simulated output from your wideband to the ecu

Cool - thanks mate! I'll read the wideband manual regarding the simulated output function.

Also, does anyone know how the cheaper NGK ones compare to the more expensive OEM Nissan ones? I checked them both out on Kudos' site.

Thanks again!

**SORRY for the double post - didn't think the stupid phone uploaded the first one!**

Edited by Peter

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...