Jump to content
SAU Community

Recommended Posts

I put 34 GTR seats in my 32 GTR. The 32 seats are way to narrow in the shoulders for me. Suggest you sit in a 34 GTR seat before you buy it/them, since they're not cheap and you want to know they feel right for your body before you throw the coins. Bolt straight it - easy job.

  • 2 months later...

Hey guys, I can't have acces to BNR34 seat because they are not allowed in my state. However, from picture, it appears the shoulder and lower curves more than R32 meaning it should hug more but then some peoples suggest that the R34 is wider so actually the r32 hug tighter ??

Thanks guys :)

Im going to be different to everyone elses posts.... The 34 seats are of course much more comfortable and being so much newer in better nick in general.

But i have had 32, 33 and 34 gtr seats and none hug me at all. im 6 foot 2 and skinny.

If your upgrading because you think they hug alot more i dont think its worth it, but if your going for comfort, looks and condition, defiantly worth it

  • 4 weeks later...
  • 3 years later...

Reviving for my two cents.  I'm a fairly fit and thin dude.  I was thinking about getting the R34 seats for my R32 just to get something newer and in better condition.  However, after sitting in them, I couldn't bring myself to do it.  They feel like regular run of the mill seats where as the R32 seats hug a lot more.  Nothing compared to a racing spec seat, but still way better, in my opinion, than the newer seats.  

It sucks because now I have to figure out what seats to get.  >.<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...