Jump to content
SAU Community

Recommended Posts

Professor Emmanuel Gay carried out a second operation to remove a large blood clot within the brain itself, after Schumacher's condition briefly stabilised Tuesday morning AEST.

The two-hour surgery successfully removed the large haematoma and subsequent scans had shown a slight improvement.But the doctors are wary of any prognosis, short term or even long term and said he was still in serious danger.

They would not be drawn on how long he would remain in a coma and said the next 24 hours was critical.Professor Gay said: "There is still some blood and haematomas everywhere, that's why the situation has to be looked at hour by hour, we are looking at a serious brain injury and the situation can still develop.

The other haematomas are not accessible, they are not of the same size as the one removed.''During the second surgery, the doctors were able to reduce the pressure on the brain and said the former Formula One driver was in a phase of relative stability.

Doctors said the first operation soon after the accident was to remove a blood clot that was just outside of the brain, and it had been too risky to eliminate the large blood clot within the brain on the left side of his head.

But surgeons took advantage of a small window of stability to conduct the second operation, which they said had resulted in better control of the intracranial pressure."On the controlled scans taken this morning [it showed the haematoma] was evacuated and the level of intracranial pressure has certainly improved, but scans shows other lesions on the brain," said Professor Gay."They will be supervised and followed and up, we will supervise situation on an hourly basis in intensive care."

The doctors earlier remarked that Schumacher would have been killed instantly on Sunday morning if he had not been wearing a helmet when he fell and cracked his head on rocks in the off piste ski area in Meribel ski resort in the French alps.

Two days after the accident, he remains in an induced coma in intensive care at the University Hospital of Grenoble with his wife Corinna and their children Mick, 14, and daughter Gina-Marie, 16, at his bedside. Other family members have also arrived to support Corinna, hospital officials said.

http://m.theaustralian.com.au/sport/motorsport/michael-schumacher-slightly-improved-but-still-critical/story-fncei7d9-1226792370825

Schumacher improves following second operation

Surgeons treating Michael Schumacher said they have detected an improvement in his condition but have cautioned that the grand prix champion is still not out of danger.

After consulting his family, surgeons performed a second operation overnight to relieve pressure on his brain.

While the doctors said there are some positive signs and there is a slight improvement in his condition, they disclosed that more lesions were discovered on his brain.

Professor Jean-Francois Payan said: “We have received a transitional improvement on the brain for Michael Schumacher which meant that we could take a new scan without putting him at risk.

“This scan showed that he is relatively stable.

“So this morning we took more scans and we have noticed we have evacuated the haematoma which is situated on the left hand side of the brain which means the situation is better controlled than yesterday.

“The scans showed that the haematoma was correctly evacuated and there was an improvement.

“But scans show that there are other lesions on the brain and show these lesions need to be kept in check and we need to check on these every hour.”

The second operation took around two hours however the medical team treating Schumacher said the ensuing hours will be crucial to the outcome.

Surgeons remain standfast in not divulging any prognosis about Schumacher’s future.

“We can’t say that he is out of danger but we now have a bit more time in the evolution.

“The hours to come will be crucial to the outcome.

“Yesterday we found a window of opportunity to do this operation at the beginning of the evening.

“With the permission of the family who also wanted to do this.

“We still can’t say we have won but there has been some highs and some lows.”

Schumacher, whose condition remains critical, remains too fragile to transfer to another hospital and any decision to do so will come at a later date.

http://www.speedcafe.com/2013/12/31/schumacher-shows-improvement-following-second-operation/

I thought they had pneumatic valves?

or are they only pneumatic assisted?

or is this a new thing with the new engines?

I'd like to know much more about the new engines, why do they have to be so secretive :P

pneumatic valve springs. they've always been cam actuated.

I'd rather watch R/C cars racing than than FormulaE, if that is what they are going to be like, especially with the ridiculous 100m dash that the drivers have to do in the middle of the race when they change cars after 20 minutes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...