Jump to content
SAU Community

Recommended Posts

  • 2 months later...

When the AWD glide was still in my car I was able to run 10.4 not using the transbrake with a real lazy footbraked 1.7 60ft launch. Tried the transbrake few times and it just spun as I didn't warm up the rear tyres in my 33GTR.

Powerglide puts the power down so smoothly compared to a manual. Defienatley had a high 9sec pass with a decent launch. Power plant was a Rb26 with hks 2530's with a manual normally make about 600awhp.

  • Like 1

When the AWD glide was still in my car I was able to run 10.4 not using the transbrake with a real lazy footbraked 1.7 60ft launch. Tried the transbrake few times and it just spun as I didn't warm up the rear tyres in my 33GTR.

Powerglide puts the power down so smoothly compared to a manual. Defienatley had a high 9sec pass with a decent launch. Power plant was a Rb26 with hks 2530's with a manual normally make about 600awhp.

Did you change back to the manual??? What happened to the box?

  • 9 months later...

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

And GTRPSI my phone app didn't let me see you post

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

Add to that 5k for the box these parts that you will require also.

Custom length and spline output shaft to suit transfercase.

Fabricated sump to clear the drive shaft when the box is massively rotated

Suitable length and angle pick tube to put the oil filter at the bottom of the new fabricated sump.

The dip stick takes some messing around to get it at a suitable height for when the gearbox is rotated.

Decent torque converter can be $1000-2000.

Shifter

Transcooler ect ect

Pretty quickly it gets to 10-12K.

  • Like 1

Add to that 5k for the box these parts that you will require also.

Custom length and spline output shaft to suit transfercase.

Fabricated sump to clear the drive shaft when the box is massively rotated

Suitable length and angle pick tube to put the oil filter at the bottom of the new fabricated sump.

The dip stick takes some messing around to get it at a suitable height for when the gearbox is rotated.

Decent torque converter can be $1000-2000.

Shifter

Transcooler ect ect

Pretty quickly it gets to 10-12K.

Exactly, and thats assuming you know what your doing......

http://shop.quaife.co.uk/nissan-skyline-gtr-6-speed-sequential-gearbox

Chuck this beast in! Perfect daily/quarter mile monster.

Rated for a lousy 750 hp. Waste of time for a "drag car".

@Ryan, have you thought about selling the output shafts and other bits as kits for GTR owners?

That way we could build up our own strengthened autos and just add the bits on to convert them to work with the GTR transfer case.

Would save everyone a shit load of development and you could recoupe some of your already made developement costs along the way.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...