Jump to content
SAU Community

Recommended Posts

What is the best way to warm up skylines? May seem like a silly question but the reason I ask is this.

With many German cars like BMW the manufacturers recommend to turn the car on, let it idle for a minute and then drive it nice and easy till it reaches the operating temp. This way the motor and gearbox warm up together.

Is this the best course to follow with a skyline or is it better to let it idle till it warms up enough and then drive?

I think I answered my self by posting this thread but would like to see what people think.

Link to comment
https://www.sau.com.au/forums/topic/440009-warmig-up-the-car/
Share on other sites

Letting the oil circulate is all that's required > then drive.

Letting the engine oil warm up is all that's required > then boost.

Letting the tyres warm up > then traction :P

Did you know that when you could hire V8 statesmans (many years ago) on a cold start you could apparently hit the rev limiter before the oil light went out? A friend told me.

To answer OP question, don't waste time sitting in the driveway idling. Cars these days (ie for the last 30 years) are designed to drive off as soon as you start them and build up oil pressure. Drive slowly / lightly until it's warm then go nuts.

learnt this with my 32,
had rough valve stem seals and warming it up on the driveway made it smoke worse

makes sence after thinking about it.

however my mate swears by starting it and after 10 seconds revving 1500 rpm constantly bliping it to 1500rpm.

recons it squirts oil up the engine. not sure but meh maby

however my mate swears by starting it and after 10 seconds revving 1500 rpm constantly bliping it to 1500rpm.

For those 10 seconds or less.......... I'm free!!!!

  • Like 2

what about warming up built/race cars?

my clutch and gearbox need to warm up before its driveable basically.

and the oil pressure is high and all over the place until its warmed up. So usually start it and either dab the throttle for a bit and leave it for 5-10mins just idling.

With a race car with a crappy tune and animal clutch you don't have much of a choice. I had a group N Daihatsu charade rally car like that once. Yes, despite only 57kW at the wheels it was a pig to drive when cold (stuck with using factory sensors on a very old F7 Haltech, and a bitey 3 puck clutch). Once it was warm it drove like the (underpowered) shopping trolley it was.

I was happy to sell that gutless POS.

Still, if you can drive the car without having to warm it up first, then that's always your best bet.

Don't know about others but when i start my r34 gtt i leave it to warm up until the needle temperature reached it's normal stance which is halfway as it takes

at least 6 minutes but thats just me.

Problem with that, as mentioned above - the oil pressure is at its minimum while its idling, and the ECU is adding more fuel to get it up to temp quicker.

Your way better just driving easily for the first 10 minutes and letting everything warm up together.

In the GTT you've got the advantage of an oil temp gauge - halfway on the coolant Temp needle could be anything. 10 minutes of light driving see's my oil temp stable at 80* and then its ready for whatever

Driveway ildling is pretty pointless, much like idling for minutes after you've stopped to cool your water cooled and oil fed turbo :)

With a race car with a crappy tune and animal clutch you don't have much of a choice. I had a group N Daihatsu charade rally car like that once. Yes, despite only 57kW at the wheels it was a pig to drive when cold (stuck with using factory sensors on a very old F7 Haltech, and a bitey 3 puck clutch). Once it was warm it drove like the (underpowered) shopping trolley it was.

I was happy to sell that gutless POS.

Still, if you can drive the car without having to warm it up first, then that's always your best bet.

the cold start tune is fine. I'm only following the clutch instructions letting it warm up before driving and stabilise oil pressure.

Don't know about others but when i start my r34 gtt i leave it to warm up until the needle temperature reached it's normal stance which is halfway as it takes

at least 6 minutes but thats just me.

Thats mental dude.

I don't think we should be looking to you for engine advice, based on your not revving over 3200 rev thread.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...