Jump to content
SAU Community

Recommended Posts

Just to let everyone know, if you are going to buy a Nissan Skyline or other up market car, the best option is Road & Road and Track Australia. I purchased my Nissan Skyline V36 SP 2006 Sedan of them, I only seen it in photos and I live on the Sunshine Coast QLD and they are in Sydney. Gavin walked me through his web site over the phone and BAM, WOW I purchased the car of him and man did I get what I wanted, NO I got even MORE, what a car, unbelievable value for money. They were the only ones that could show and guarantee the K's on the car. I tried others and when I mentioned about providing proof of K's NO ONE answered back, only GAvin from Road and Track in Sydney. I couldn't even dream the type of car I received from them and they sent it to me in QLD, I picked it up yesterday. I nearly wet my pants with excitement, amazing, the smell of leather just like a brand new can with 50000K's you would pick it, its just like a new car in and out, goes like a rocket, just like a 1100cc road bike, I think it would leave the bike behind. No wonder they don't allow P plate's drive the car. they would kill them selves on the fist corner. So if you want a car buy it from Gavin. NO MATTER where you live you will receive better than you expected. Just look at the types of cars he provides for people like us. A1+++++. Don't be a foll and buy else where, you are mad if you do. WHOOOOOOO HOOOOOOO Gavin thanks heaps. Your the MAN.

post-135533-0-18112300-1405721702_thumb.jpg

post-135533-0-09473100-1405721704_thumb.jpg

post-135533-0-18238800-1405721706_thumb.jpg

post-135533-0-07484400-1405721708_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/445806-where-to-buy-a-nissan-skyline-v36/
Share on other sites

Seems like a very spammy post...

More info on k's guarantee please.

Post vin.

Have you ever been on a motorbike? A 600 would smash your car.....

Edited by Ben C34
  • Like 2

That said, I purchased my 370 from Gavin, and can vouch for the above...with the exception of near breaches of urine, and apparent twin turbo systems allowing you to defeat 1100cc bikes.

Got curious so checked out their site. Found this. Interesting and good on em.

All cars sold by Road and Track are covered by our Mileage Guarantee. All our vehicles have full documented history including service history and log books. For our vehicles imported from Japan, Road and Track have also pioneered odometer certification checks performed in Japan by an independent certifier, who issue the vehicle with an odometer certificate that confirms the authenticity of the odometer reading.

Road and Track are pioneers – Never before has an importer of Japanese vehicles been able to offer a mileage guarantee – Road and Track guarantees all our vehicles!

We are confident you won’t buy better anywhere else! Talk with our sales team today!

These cars are actually P Plate legal in QLD, as are 350z....

Tony, can you provide documentation on this? Does it stretch to Learners as well? Everywhere I've looked says they're QLD banned. Edited by Simink

TMR website.

The existing definition will continue to apply to cars manufactured before 1 January 2010. Under this definition a car is a high-powered vehicle if it has:

an engine with 8 or more cylinders

a turbocharged or supercharged engine that is not diesel powered

an engine with a power output of more than 210kW

a rotary engine with an engine capacity of more than 1146cc

an engine modification that must be approved under section 13 of the Transport Operations (Road Use Management—Vehicle Standards and Safety) Regulation 2010 (PDF, 831KB).

http://www.qld.gov.au/transport/licensing/driver-licensing/applying/provisional/restrictions/index.html

These cars are marketed as producing 206kw,hence legal.

an engine with a power output of more than 210kW

These cars are marketed as producing 206kw, hence legal.

Not doubting you, but everywhere I've looked they've been more around the 215-220kw+ mark.

I'll have to do some more digging on that! :yes:

Seems like a very spammy post...

More info on k's guarantee please.

Post vin.

Have you ever been on a motorbike? A 600 would smash your car.....

To certify K's is with the full log book service history showing K's on each service from the 1st purchase date. Also when the car is registered for the 1st time it will show K's and each year when the renewal of rego it shows the K's every time. JEVIC is the company that certifies odometers and supplies a certificate of authenticity, when it's true and correct. http://www.jevic.com/services/vehicle-maritime-inspections/odometer-verification. This is what my car came with.

Also I would love to see what would really happen if you put the V36 SP againts any bike, I don't think the 600 would beat it to the 100k's p/h. It would be great to see.

To certify K's is with the full log book service history showing K's on each service from the 1st purchase date. Also when the car is registered for the 1st time it will show K's and each year when the renewal of rego it shows the K's every time. JEVIC is the company that certifies odometers and supplies a certificate of authenticity, when it's true and correct. http://www.jevic.com/services/vehicle-maritime-inspections/odometer-verification. This is what my car came with.

Also I would love to see what would really happen if you put the V36 SP againts any bike, I don't think the 600 would beat it to the 100k's p/h. It would be great to see.

LOL!!

Have you ever ridden a bike in your life?

Most 600cc Sportbikes will do 0-100 in about 4 secs. A twin turbo V36 would barely even do that with drag radials!

My old Suzuki SV 650 was about 50kW and it still did 0-100 in around 4 secs. A stock V36 does 5-5.5 secs......

Not doubting you, but everywhere I've looked they've been more around the 215-220kw+ mark.

I'll have to do some more digging on that! :yes:

You are correct, the 206kw figure is only for the VQ35DE in the V35 and pre 2005 350Z.

The V36 has the VQ35HR engine rated at 230KW and is therefore restricted for p-plate drivers.

I don't think the 600 would beat it to the 100k's p/h. It would be great to see.

You would need to go against a 600cc sports bike that is actually trying.. you wouldn't have a chance!

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...