Jump to content
SAU Community

Recommended Posts

So after having promised to do this long ago and report back, I finally pulled my finger out of my bum about a month ago and decided to get the V36 tuned to see if there was anything to be gained from it.

In short, no.

I wasn't expecting much of a boost in power. That would be unrealistic of anyone to think so. Another 12kW was produced as a result of this tune, not that my arse-dyno can feel the difference, but at least scientifically, I can now say I have just over 200kW at the wheels. :P

More to the point though, as you'll see in the attached graphs, it's pretty clear that these vehicles are pretty damn well tuned out of the factory. There's no improvement in response. Fuel economy, I've yet to determine as I've only been driving it out on weekends when I haven't needed to load the drums in the wagon instead. I'll give it about three full tanks to see how it averages out but I doubt I'll witness any major improvement to be honest.

Until then, I'll save my final verdict. My preliminary verdict, in the meantime, is that there's no point in wasting your cash doing a dyno tune in its naturally aspirated configuration. Best to save it for the day you decide to whack a Stillen supercharger kit instead.

post-65137-0-45964800-1418452721_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/451709-ecutek-flash-tune-dyno-results/
Share on other sites

Very similar result to a stock 00 WRX I had Ecutek 'd some years ago by MRT in Sydney.

But--

--different story when I then changed out the OE intercooler to bigger AVO/ exhaust to turbo back SMB SS 3"/ Air inlet pipe to Samco silicon/ airbox to custom with Apexi filter/ 0E BOV to GFB Stealth , Fuel pump to Walbro /Fuel regulator to Malpassi (rising rate) and Turbo to a VF28- then had it retuned by Mercury in Brisbane using Ecutek Stage 3.

:w00t:

You have a mild torque increase across the entire rpm range, surely you'd notice that? Maybe it's so subtle you're using less throittle to achieve the same rates of acceleration and not noticing it, but I guess that should show up as reduced fuel consumption.

It's a shame you weren't able to do some before-and-after runs at the drag strip where it might make itself more apparent. Either way I'd be happy with torque and power curves like that. You're right though, for the money it's probably not worth the effort unless the fuel economy has significantly improved.

I agree with Matt, the torque increase and response you get should be pretty noticeable, I know mine was. But yeah, money spent wise it may not be the best. I am quite happy with my UpRev tune, considering I can keep up with some of the Subaru Liberties and WRXs....minus cornering haha well I'll just drift around them corners

  • Like 1

So how much did the UpRev work out?

And is there a fuel consumption benefit? With the 3.7 it is already doing 8-9l/100km on a run, but just curious to see if the tune affects it.

How are you getting 8-9l/100kms?

I get about 12-13l/100kms :( then again I work 5 mins away from home with stop go every 200m or so...and I drive like an asshole too :P

I paid $550 for my UpRev tune. But decided to buy the cable and upgraded my license to the tuner license. If you have money to burn, get it tuned for the better torque =D

Edited by colin.ssc

it is already doing 8-9l/100km on a run, but just curious to see if the tune affects it.

Do you mean 8-9km/L (the dash output is in km/L)?

If not, I want to know how you manage that too

Lol I know...the missus always goes quiet when I start driving with the foot down...and then death stares....hahaha...can't imagine if it was twin turbo'ed

When you have a car with power you don't have to drive like a hero everywhere.

The best i got from my 6MT was around 12km/L and the worst has been 8km/L and i got intake, HFC, Y-pipe back exhaust, 20*10 wheels all round and Tony getting 6km/L seems a bit off as i have a heavy foot too and almost always rev out the first gear usually. You guys go on the reading on the on board computer or when you fill up again? i go on the later one as thats more accurate imo.

On another note since i got a new intake few months ago (before having just drop in filters) i have noticed the car leaning out around 3000-3500 rpm(hesitating to rev) before if takes off again like some boost came on. Im guessing having this tune will fix the lean out wouldnt it? I got an HKS obd2 reader with my phone and the AFR learn is running +/- 20% (use to be around 5-8% before intakes).

Any one have any information on this would be great. Thanks

So if the answer is yes to getting a tune whats the better way to go UpRev or EcuTek

Edited by AsM

8 or 9 l/100km is the norm on a decent freeway run, in 7th at around 2,000 rpm on cruise...

Kids to school is more like 12 l/100km, which is still slightly better than the M35 Stagea 2.5 Turbo that we used to have. This is measured from the OBD2 port using a Garmin bluetooth device. Loving having full OBD2 compliance...

When you have a car with power you don't have to drive like a hero everywhere.

I dont drive like a hero everywhere. I do it occasionally just for the fun of it, on empty roads. And I, like Tony and ASM have pretty heavy foot. Doesnt mean I red line the car all the time. I just get off traffic lights at 3.5-4k revs etc.

I just drive with abit more urgency than she would like me to but I come from a country where we drive with urgency and not braking all the time when people merge into your lane or changing lanes. If you come to Perth, you'll see the idiots all around driving on the right lane doing 80km/h in a 100km/h zone. I'm nt gonna just sit behind these assholes cause they cant drive properly

8 or 9 l/100km is the norm on a decent freeway run, in 7th at around 2,000 rpm on cruise...

Kids to school is more like 12 l/100km, which is still slightly better than the M35 Stagea 2.5 Turbo that we used to have. This is measured from the OBD2 port using a Garmin bluetooth device. Loving having full OBD2 compliance...

Lucky you, I guess the 7 spd gear box does give better fuel economy. Too bad I chose to get the 5spd instead.

When you have a car with power you don't have to drive like a hero everywhere.

It's spirited driving, not heroic. I don't weave in and out, cutting people off like many wankers do.

I don't do ab crunches either (taking off at the lights like a madman and stop accelerating when you reach 60km/h). I've called one of my buddies a retard for constantly doing that in his Magna back in the day. Stupid, wasteful and just uncomfortable when you're a passenger.

Edited by The Max

You guys go on the reading on the on board computer or when you fill up again? i go on the later one as thats more accurate imo.

MyFuelLog Pro app which takes odometer and fuel fill quantity figures.

I should note though, that's city driving. I get 7.7km/L when on the open road. Again, spirited driving. :)

So if the answer is yes to getting a tune whats the better way to go UpRev or EcuTek

I hear EcuTek can do valve timing as well but you wouldn't be missing out that much if you go with the UpRev. Edited by The Max

I hear EcuTek can do valve timing as well but you wouldn't be missing out that much if you go with the UpRev.

How much did you pay for EcuTek in Aus if you mind telling me? or pm whatever you prefer thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...