Jump to content
SAU Community

Recommended Posts

Hey guys I just bought a R33 GTS-T and it's a great car but the tyres on it are on there way out. I've been driving it around a bit and in the dry they seem ok but in the wet and not even on a hill there is no way I can take off without losing traction. Basically what I'm looking for is a set of tyres that have good grip in the wet and don't make too much noise.

What do you guys recommend? I am thinking of going with the Bridgestone Potenza Adrenalin RE002.

By the way I did look at the sticky post but there is too many pages and different ratings on tyres. My price range is flexible, obviously cheaper the better but if I have to fork out for a good set I do not mind - probably keep it under $1000 for a set though.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/452541-r33-gts-t-best-tyres-for-in-the-wet/
Share on other sites

KU31. Cheap, cheerful and they work.

KU36. Cheap, cheerful, stick like shit to a blanket, noisy as buggery, but worth it.

There are many other options, even some very cheap ones, such as the Federals, Achilles, etc.

Most serious brand (Goodyear, Dunlop, Bridgestone, Pirelli, Yokohama, Toyo, etc) tyres that are not really OLD (like the FK452) are going to cost more than $1k per set.

Perhaps I should confess that the 36s are not the BEST in the wet. They work fine in the wet, but they won't handle standing water. Not enough tread on them to pump a LOT of water. But I've never had low confidence with them in winter. Just don't lean on them cold, and don't try to tow skiers.

I'm a big fan of Maxxis tyres and they are more than reasonably priced. I have a pair of terrible tyres on the back of my GTST at the moment that came with the wheels I bought, they do the same thing in the wet as you describe. After a good research session the other day I settled on getting a couple of Maxxis MA-511 to replace them. They seem to be a newer version of the Maxxis MA-V1 which I have had a set on the front for years and can't say enough good things about.

A good tyre review and opinion site to check out and see how a potential purchase is going to stack up is http://www.tyrereviews.co.uk/

Edited by Malakai

Nitto INVO tyres aren't too bad in the wet either and provide decent dry weather grip.. Great daily tyres IMO and not too noisy.

At the same time, perhaps look at lightly shimming up the diff OR just going with a new mechanical diff. I find the stock VLSD likes to single peg on days, it's very temperamental like a female.

I'm running Goodyear Eagle Asymmetric 2 in 17" and they are really quite good in both dry and wet. Paid about $900 new for a set online. Always check the date of manufacture before buying though.

I'm running Goodyear Eagle Asymmetric 2 in 17" and they are really quite good in both dry and wet. Paid about $900 new for a set online. Always check the date of manufacture before buying though.

I just took a set of those off my car. Totally underwhelming tyre. Not awful. Just.....not great. Only lasted 12000km.

I just took a set of those off my car. Totally underwhelming tyre. Not awful. Just.....not great. Only lasted 12000km.

Interesting, what did you have prior and what are you running now, out of curiosity?

KU36 before. And oddly enough, KU36 again. I was actually intending to get RS-3s, but they're unavailable for the next 3 months.

The Goodyears had this horrible tendency to judder as I turned out of my driveway (like......really really low speed understeer!). I spent ages trying to work out if it was a tyre issue or an alignment issue, including spending on 2 extra alignments that the car wouldn't have gotten. So, on the Tuesday morning with Goodyears on it judders on the way out. On the Wednesday morning with the KUs on, no judder. I think that answered that question. That sort of crap pretty much explains my experience with the Goodyears.

I've used KU36 probably 7/8 years ago - wasn't a total fan of them to be honest..

But then again, they were never taken on the track. I found they did like to understeer until it had some decent heat through them

Maybe. Dunno about that pricing here in Adelaide though (as in, getting Nitto for pricing that's competitive with the KU36 price). The Tyrepower store I use are good blokes who are aware that I have previously bought in tyres from the eastern states and from the US to get good stuff at good pricing, and so they tend to offer me the best pricing that they can. They handle Nitto also, and the pricing on them was not attractive last week.

I'm up for new tyres soon too, not sure I want to put NT01s at the rear.. that might result in a broken gearbox :(

I'm running NT01 at the front, surprisingly they're not too bad in the wet!

Ive got Hankook Ventus 452s on the mrs car and also on my XR6 work ute which has an alloy tray and even in the wet in 1st gear the traction control light doesn't come on! Pretty impressive all rounders actually. They are quiet with very good grip wet and dry are reasonably priced.

I also am not a fan of the KU36. The RS-3s shit all over them in all conditions and are also probably a bees dick quieter. But they aren't what you'd call quiet lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...