Jump to content
SAU Community

Recommended Posts

Buy a 1989 nothing model, by that logic.

I am going to guess your after something more collectible and rare by the sound of this question.

In which case the ADM poops all over the nismo

Is this a survey question as a matter of interest? Or are you actually interested in buying one?

I personally would go with the Nismo out of those two. The Nismo is not actually that different to the stock GTR. They made a few slight changes, including full Nismo body kit (front bonnet lip, front bumper vents, Nismo sideskirts and Nismo Back boot lip), No rear windscreen wiper, no ABS and no AC as per standard. They also included slightly larger turbos (which are laggy and too large to be efficient at 0.8 bar). These were mostly to modify the aerodynamics of the R32 GTR for Homologation for Grp A racing. Grp A cars were not supposed to look the same as the factory car, which included spoiler kits etc. In stock form, the Nismos were not really any faster than standard R32 GTRs.(See youtube below)

However, in saying all of this, everyone knows that the Nismo is the base for such historically classic race cars as the Calsonic GTR etc. Even though the Nismo has more units produced than the ADM, 500 (plus 60 odd that went directly to grp A teams) vs 100 for the ADM, internationally the demand for Nismos will outstrip the ADM 1000:1. So that should mean that the number of buyers competing for the few Nismos remaining ( I assume that many of them have been raced and crashed), should always mean that the Nismos command a higher purchase price.

As im a kiwi and not Australian, i have no real interest in the ADMs at all, so maybe i am bias. Aussies will have to jump in here and give their points of view too.

Possibly a better question is ADM vs Nismo vs N1?

N1s only had 228 units produced, vs the 500 (plus 60) Nismos, vs the 100 for the ADMs. Unlike the Nismos (Group A), the N1s were for Group N endurance racing (off the show room floor racing). In the early 90s, Group N racing in Japan was very similar to Bathurst in the early 70s. You buy a car from a manufacturer, make very limited mods (tyres, brakes, suspension, exhaust and computer i believe) and then race it! So the GTR N1 was a semi prepped race car from Nissan. So the chassis is more rigid, engine built by hand, bigger turbos, lighter everything etc. Of the 228 R32 N1s Built, they can be split into 3, N1, V Spec N1 and V Spec II N1. To be honest i am not 100% sure of the exact break down in terms of quantity, but i believe that most of them were the initial N1 spec and the V Spec N1 and V Spec II N1 number approximately 50 each.

From what i can tell from my general observations, N1s sell for approximately 25-30% more than Nismos in Japan. This is simply my general observations over the last 3 years. It is very hard to work out accurately with such a small number coming up for sale and condition varying so much.

So in my mind, the wish list order in terms of both value and desirability for an Australian wanting to buy an R32 GTR should go like this (all things remaining equal)

1 - V Spec II N1

2 - V Spec N1

3 - N1

4 - Nismo

5 - ADM

6 - V Spec II

7 - V Spec

8 - Stock GTR.

Of course this is just my opinion and everyone is different.

  • Like 2

Great reply thanks.

Ye I was looking at purchasing one or the other , and purely based on collectability atm ,but I'm not sure weather they are worth 10 or 30 grand more than a standard gtr or Tommy Kaira gtr ?

Obviously that is all an individual point of view. Most people would probably say that double the price for a car that is almost identical, with the main difference being a little blue chassis plate, is probably not worth it. However then you get people like myself, that willing to pay 3 x as much or more for that different little blue build plate, just to say i have an N1! I would say that all bar the Tommy Kaira is a good investment. I cant see too many people demanding Tommy Kaira's with too much enthusiasm.

An N1, Nismo or ADM will all be solid investments and more importantly great cars with which you will be proud to drive.

The ADM will, in this country, always out strip the Nismo version. Prior to the 35 Australia was the only country Nissan exported the GTR directly too.

That being said I would dearly love an N1.

Is this a survey question as a matter of interest? Or are you actually interested in buying one?

I personally would go with the Nismo out of those two. The Nismo is not actually that different to the stock GTR. They made a few slight changes, including full Nismo body kit (front bonnet lip, front bumper vents, Nismo sideskirts and Nismo Back boot lip), No rear windscreen wiper, no ABS and no AC as per standard. They also included slightly larger turbos (which are laggy and too large to be efficient at 0.8 bar). These were mostly to modify the aerodynamics of the R32 GTR for Homologation for Grp A racing. Grp A cars were not supposed to look the same as the factory car, which included spoiler kits etc. In stock form, the Nismos were not really any faster than standard R32 GTRs.(See youtube below)

However, in saying all of this, everyone knows that the Nismo is the base for such historically classic race cars as the Calsonic GTR etc. Even though the Nismo has more units produced than the ADM, 500 (plus 60 odd that went directly to grp A teams) vs 100 for the ADM, internationally the demand for Nismos will outstrip the ADM 1000:1. So that should mean that the number of buyers competing for the few Nismos remaining ( I assume that many of them have been raced and crashed), should always mean that the Nismos command a higher purchase price.

As im a kiwi and not Australian, i have no real interest in the ADMs at all, so maybe i am bias. Aussies will have to jump in here and give their points of view too.

Possibly a better question is ADM vs Nismo vs N1?

N1s only had 228 units produced, vs the 500 (plus 60) Nismos, vs the 100 for the ADMs. Unlike the Nismos (Group A), the N1s were for Group N endurance racing (off the show room floor racing). In the early 90s, Group N racing in Japan was very similar to Bathurst in the early 70s. You buy a car from a manufacturer, make very limited mods (tyres, brakes, suspension, exhaust and computer i believe) and then race it! So the GTR N1 was a semi prepped race car from Nissan. So the chassis is more rigid, engine built by hand, bigger turbos, lighter everything etc. Of the 228 R32 N1s Built, they can be split into 3, N1, V Spec N1 and V Spec II N1. To be honest i am not 100% sure of the exact break down in terms of quantity, but i believe that most of them were the initial N1 spec and the V Spec N1 and V Spec II N1 number approximately 50 each.

From what i can tell from my general observations, N1s sell for approximately 25-30% more than Nismos in Japan. This is simply my general observations over the last 3 years. It is very hard to work out accurately with such a small number coming up for sale and condition varying so much.

So in my mind, the wish list order in terms of both value and desirability for an Australian wanting to buy an R32 GTR should go like this (all things remaining equal)

1 - V Spec II N1

2 - V Spec N1

3 - N1

4 - Nismo

5 - ADM

6 - V Spec II

7 - V Spec

8 - Stock GTR.

Of course this is just my opinion and everyone is different.

Good reply indeed. In Australia, rankings #4 and #5 are likely to be switched, or equal.

On the world stage, yes, the Nismo model would be worth more than the ADM.

Projected Sums Insured by Aust. Insurance Companies should be in 2015 in Renewal terms...

(for top of the line specimens) around...

* V-Spec II N1 - $95,000

* V-Spec N1 - $88,000

* Non V-Spec N1 - $80,000

* Aust Delivered - $78,000 to $83,000

* Nismo - $75,000 to $85,000

* V-Spec II - $53,000

* V-Spec - $43,000

* Non V-Spec - $33,000

Mods in my opinion (depending on what they are) might only shift those values north by a small margin.

That'll be negotiated I'm sure between the owner and the company.

Good reply indeed. In Australia, rankings #4 and #5 are likely to be switched, or equal.

On the world stage, yes, the Nismo model would be worth more than the ADM.

Projected Sums Insured by Aust. Insurance Companies should be in 2015 in Renewal terms...

(for top of the line specimens) around...

* V-Spec II N1 - $95,000

* V-Spec N1 - $88,000

* Non V-Spec N1 - $80,000

* Aust Delivered - $78,000 to $83,000

* Nismo - $75,000 to $85,000

* V-Spec II - $53,000

* V-Spec - $43,000

* Non V-Spec - $33,000

Mods in my opinion (depending on what they are) might only shift those values north by a small margin.

That'll be negotiated I'm sure between the owner and the company.

That is a very interesting list Terry. Im sure you know alot more about the price of these in Australia than I do. Iron Chef may be able to help with this, but i would have thought that the price gap between N1s and Nismos in Japan, would have been mirrored or at least have some correlation with the price gap of N1s and Nismos in Australia. Again it is only my observation, but i would have thought that a Nismo would command around 25% less than a similar condition N1. Again this is only observation and also i may be bias :)

  • 2 weeks later...

This NISMO will be a good guide.

I'm trying to find out the sell price on this (If it sold).

http://www.j-spec.com.au/auction/SEVS/1990-Nissan-Skyline-5701471.html

Bob.

  • 5 weeks later...

So roughly what would a Nismo in good condition be worth in Aus

This car sold for the equivalent of approx. $50,000 landed complied and registered.

http://www.j-spec.com.au/auction/SEVS/1990-Nissan-Skyline-5701471.html

That's pretty much inline with an Australian Delivered R32 GT-R.

I'd say they are worth roughly the same money all things considered.

Bob.

post-78207-0-87424700-1428307553_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...