Jump to content
SAU Community

Recommended Posts

nismo-logo.png


BRAND NEW GENUINE NISMO LEATHER SHIFT KNOB - $75.00 DELIVERED.

leather..jpg


Item Details: 100% Genuine Authentic Nismo Leather Gear Knob
Condition: Brand New

The NISMO Leather Gear Knob has a beautiful leather skin covering and a solid body made from a special plastic which minimise vibration transfer from the gearbox.
Direct replacement for Nissan 5 speed & 6 speed manual gearboxes.
 
Part Number: 32865-RN003

map-s_32865rn003.jpeg
DIMENSIONS:
- Screw size: 10mm (M10 x 1.25)
- Width: 40mm
- Length: 72mm
- Inner Length: 59mm


SPECIFICATIONS:
Material: Leather
Shift pattern: Includes 5 speed shift pattern sticker

Vehicle Compatibility List:

- Nissan Skyline R32 (All, With GTR/GTS-4 Make sure Thread is 10mm)
- Nissan Skyline R33 (All).
- Nissan Skyline R34 (Including GTR 6 speed gearbox)
- Nissan Stagea WG(N)C34 (All)
- Nissan 180SX R(P)S13 (All)
- Nissan 200SX S14 (All)

- Nissan 200SX S15 (6 speed)
- Nissan 300ZX Z32 (All)
- Nissan Pulsar N14 (Inc GTI-R)
- Nissan Pulsar N15 (All)
- Nissan Pulsar N16 (All)
- Nissan Silvia (P)S13 (All)
leather_1.jpg


PM me or Visit my website to purchase - Addtocart.gif

Fits v36?

Im not 100% sure sorry. Nismo dont list them to suit however, if your car has the 10mm (m10 x 1.25) thread, then it should fit.

Sorry I cannot confirm this 100%.

  • 2 weeks later...
  • 2 weeks later...

Has anyone fitted this to a V36 manual coupe or z34 ? just wanna know how it will sit once installed as the factory one is quite short....

I had a bit of search on this but couldnt find anything sorry. Do you know the dimensions of the shifter thread/stick section?

  • 3 weeks later...
  • 6 months later...
  • 4 weeks later...
  • 3 months later...


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...