Jump to content
SAU Community

Recommended Posts

Applies to 4 pistons. Serious. Not theory. Shit is real.

I need.to read up on all of this. As well as bring some of these concerns to the guys that run them over here. If I was to buy a brembo big brake upgrade. I would guess all these issues would be addressed. This is crap because im all about functionality then looks. Wow. I can see myself basically taking a course on these valid points. Here goes the reading. Ok. If it was you guys is there any way of addressing these problems feom the info you've seen.

Thw bleed screw one is valid. Any others???

master cylinder and brake bias

I need.to read up on all of this. As well as bring some of these concerns to the guys that run them over here. If I was to buy a brembo big brake upgrade. I would guess all these issues would be addressed. This is crap because im all about functionality then looks. Wow. I can see myself basically taking a course on these valid points. Here goes the reading. Ok. If it was you guys is there any way of addressing these problems feom the info you've seen.
Thw bleed screw one is valid. Any others???

The 6pot would be overkill, like Fred Flintstone Panic Braking.

So what is the difference between 6 pot and 4 pot? Running the same rotor and pad will often mean less braking power!!!!!! NOT more!!!!!!

There are loads of threads posted about this sort of the stuff. Maybe people should read the EVO caliper thread to get an idea. People shoudl think of brakes as simply heat sinks. So you are not trying to stop quicker, but rather stop more consistently. So you handle more heat largely with the rotor so everything the caliper does it based around what the rotor needs.

Good pads and fluid. Good curved vane rotors of bigger diameter...and frankly its pretty silly to use less than ideal lug mount caliper adaptors rather than go to a proper radial caliper. Especially when the piston sizes are going the wrong direction. ie the bigger the rotor you choose the run you actually want to go to a caliper with less piston area...NOT more. So going from a 280-296mm std Nissan rotor to a 355mm rotor you dont want to be going to a caliper with bigger pistons than the std 40.4mm pistons

  • Like 1

Off topic but would there be any advantage to using a larger rotor with the factory caliper via the use of an adapter of some sort? Forget the cost to benefit ratio I'm just curious whether it would increase performance and reduce brake fade.

Just had the thought because more people use 17/18 inch wheels than the factory 16s

Edited by Blackkers

Off topic but would there be any advantage to using a larger rotor with the factory caliper via the use of an adapter of some sort? Forget the cost to benefit ratio I'm just curious whether it would increase performance and reduce brake fade.

Just had the thought because more people use 17/18 inch wheels than the factory 16s

Yes definitely better. To actually be able to fit an adapter though the difference in rotor size needs to be a fair bit.

Yes definitely better. To actually be able to fit an adapter though the difference in rotor size needs to be a fair bit.

And then you start to get into the problem of the larger diameter rotor not fitting nicely into the shape of the caliper or the pad not sitting nicely on the rotor.

So it works for some cases, not for others.

  • Like 1

hugely overpriced given what the parts cost, 6 pots can by had for us$500 plus shipping brand spankers.

Not even that.

I priced them at US149ea

Even Jegs and Summit have them for around 155-160us ea

Brackets are 160ish US

The Calipers are cheap because GM order them by the millions. So of course, they cost f**k all.

997 GT3 cup calipers arent that expensive either.

Yeah about $700 when I last checked.

Problem is cost to get them fitted makes things expensive - and the time factor.

Hence a 'bolt-on' Skyline kit, ready to go and can be done in a couple hours, is always handy.

The Calipers are cheap because GM order them by the millions. So of course, they cost f**k all.

Yeah about $700 when I last checked.

Problem is cost to get them fitted makes things expensive - and the time factor.

Hence a 'bolt-on' Skyline kit, ready to go and can be done in a couple hours, is always handy.

Very true.

Been looking at those brackets that US mob are making....cant say im a fan....look like they would flex a whole bunch! being 10(ish)mm aluminium.

Though I may buy the 4 pot brackets, and If I'm unhappy, have the bracket remade in 4140 or something.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...