Jump to content
SAU Community

Recommended Posts

Not that I care, but when modifying a car it has to all meet the ADR standards.

No changing can allowed, no more than a 20% more power etc.

There's something about changing to an older engine somewhere, which is a no no, but given an rb30 comes out with one cam, using a different head and cams although stock, is still changing the cam.

That's easily sorted by an emissions test though.

The 30 bottom end and 26 or 25 head is a bit of an oddball as far as the standards and law goes.

Agree this setup is perfection ^^^ if i was to go a single it would be very similar.

All will get sorted. Just needs time.

Nice to hear there is some hope among the gloom :)

I know I will be happy when it is done and love the way it drive already, I think it will be a good hill climb car.

The old set up was crap compared to how it drives now, even with the existing problems I am happier :)

Illogical statement.

It was crap because the set up for your previous engine was crap.

That's why you are having the issues now because you are using the same suboptimal setup for your new engine, which is crap right now. Right?

Logical isn't it?

Not having a go at you, just saying now you have the knowledge that your set up from when you bought the car was suboptimal you know why it drove the way it did. Don't ignore the elephant in the room when you are critiquing your previous setup.

Anyway all the best with it and I hope you get exactly what you want and even better than what you expect. :)

Illogical statement.

It was crap because the set up for your previous engine was crap.

That's why you are having the issues now because you are using the same suboptimal setup for your new engine, which is crap right now. Right?

Logical isn't it?

Not having a go at you, just saying now you have the knowledge that your set up from when you bought the car was suboptimal you know why it drove the way it did. Don't ignore the elephant in the room when you are critiquing your previous setup.

Anyway all the best with it and I hope you get exactly what you want and even better than what you expect. :)

What previous set up are you referring to , 1 when I bought it, 2. when I changed the cams, turbo and exhaust 3 the 3.2 and this one is not finished yet and when it is I expect it to be what I wanted to begin with, fingers X :)

Here are the 3 dynos

post-52098-0-08192200-1431414670_thumb.png

post-52098-0-74572700-1431414882_thumb.jpg

post-52098-0-95983100-1431415049_thumb.jpg

So do you have a pic of the harmonic balancer ?

Cause if it is in fact controlled by the factory CAS that could be the issue :(

I picked that the build will require a crank trigger to sort out timing issues ages ago....

Those where the pics i've been looking for

Doesn't look like it has a trigger wheel :(

Factory CAS could very well be the issue :/

I hope not but I've seen it to many times

what problem does this cause

Timing scatter at high RPM due to the longer timing belt, this is the problem when an engine is controlled by what is realistically a rubber band

My advise now is DO NOT push this engine till the problem is confirmed just in case cause timing scatter can cause big problems

Timing scatter at high RPM due to the longer timing belt, this is the problem when an engine is controlled by what is realistically a rubber band

My advise now is DO NOT push this engine till the problem is confirmed just in case cause timing scatter can cause big problems

thanks for that, could have saved me a bigger problem, didn't need anymore :)

Glad you said that I was going for a run today and I have been too busy with the kids for a while.

I will ask them if they ut a trigger wheel on

Pete you'd know if they did, it would be on the bill. Until the murrayis kit came along they were not cheap.

Not on the build sheet or the earlier build before I bought the car, just the ATI balancer and damper ??

Do they make that much difference or more a safety precaution for the motor ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...