Jump to content
SAU Community

Recommended Posts

OK spark plug, cam and timing belt covers sold. Still for sale:

6 Volk Racing Le37 in 18x9.5 +12 $2,500

Wideband 02 sensor controller $180

Battery Box $20

2x 32 Heater core and box $80

JJR RB26 sump baffles $250

R34 GTT/C34 Stagea Series 2 Oxygen Sensor $90

Ruzic Datalogger and Engine Monitor II $500

Plenum $200

Walbro e85 fuel safe pump $200

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 months later...

Walbro fuel pump gone.

Now added, radiator cooling panel to suit W34 Stagea from the original Bass Junky group buy, $150

cooling-panel1.jpg

cooling-panel2.jpg

So the current list of for sale is:

6 Volk Racing Le37 in 18x9.5 +12 $2,500

Wideband 02 sensor controller $180

Battery Box $20

32 Heater core and box $80

JJR RB26 sump baffles $250

R34 GTT/C34 Stagea Series 2 Oxygen Sensor $90

Ruzic Datalogger and Engine Monitor II $500

RB26 Plenum $200

Stagea Cooling Panel $150

Sorry yes the plenum is bare other than the air temp sensor; although if you need particular bits I probably have them...

Re the Ruzic Data logger.  Basically Paul Ruzic (Mountainrunner on here) was (is?) a skyline owner and electrical engineer who built limited runs of a couple of excellent units.  I'm selling the Engine Monitor and Data logger, they work together to monitor 23 channels of data, and bring them to your attention if there is an issue (eg low oil pressure, high oil or water temp etc etc).  It comes with software to configure each of the inputs.

When an alarm is triggered you can get warning light and/or buzzer, it also comes with a shift light and the EM has a configurable screen than can show 4 pages of 4 values.

You (or an auto elec, or a good workshop) will need to wire in whichever data you want to log. I had oil temp and pressure, coolant temp, fuel pressure, revs, volts, speed, rpm, 4wd%, afms, air temp, injector%, timing, TPS, wide band 02, brake switch, engine check light. And GPS location and speed of course

Available channels for the Engine monitor:

ruzic-em.jpg

Available channels for the Data Logger:

ruzic-dl.jpg

The 2 units share data so all DL channels can trigger warnings, and all EM channels can be logged.  It logs to a USB stick for easy changes and transfer to a PC

There must be a few engine monitors out there because I got one from the second batch, not sure how many data loggers he made.  Also his attessa controller (which I don't have) is excellent and links in too.

When I decied to go e85 with flex fuel I went Haltech, as part of the change I went to their dash as well to keep the car simple. 

  • 2 months later...

lol, you mean other than a major PITA?  I'll check something out but I don't have access to anything other than retail couriers

  • 3 months later...
  • 3 years later...
46 minutes ago, RobsgottaGTR said:

I am interested in the wheels!  Ready to purchase.  Message me here or on Instagram @robs_gotta_gtr

PM sent!

  • Like 1

Yeah it's been a while, but not everything is sold...I need to recheck everything and probably just start a fresh thread 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...