Jump to content
SAU Community

Recommended Posts

1 hour ago, Count Grantleyish said:

That's true!

Everyone else's took forever. Mine isn't out and I'm hoping it stays that way unless I find broken mounts lol 

Trust me you don’t need to remove the engine for mounts, we just happened to find the mounts after removing the engine 

52 minutes ago, r32-25t said:

Finally got to drive it an anger and no engine protection issues and I can hold the steering wheel with one hand under full power now

That means it isn't powerful enough. 

  • Haha 1
18 minutes ago, Count Grantleyish said:

Add another Precision turbo to the side of 'ol 26. 

I could do that but I’m not at the limit of this one just at the sensible limit of the standard engine hehe

  • 3 months later...
On 07/07/2020 at 6:14 PM, r32-25t said:

Am entered in roll racing on Friday night, so doing a the usual checks and crossing my fingers everything goes smoothly 

Sounds like a Samsonas was added, I heard they only let cars with sequential only race now ?

  • Haha 2
51 minutes ago, r32-25t said:

No chance of either of those touching my car 

I reckon I'll smoke you in my R1 GTR mate,

honestly...

p.s. i flatshift at 8850rpm.

z-tune engine vs brett single turbo from a standstill, show me the money pal (and if i win you have to reply to all my sau posts and refer to me as big daddy)

10 minutes ago, BakemonoRicer said:

I reckon I'll smoke you in my R1 GTR mate,

honestly...

p.s. i flatshift at 8850rpm.

z-tune engine vs brett single turbo from a standstill, show me the money pal (and if i win you have to reply to all my sau posts and refer to me as big daddy)

And if you lose?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...