Jump to content
SAU Community

Recommended Posts

As someone who has been through the shitstorm that is a fire / total loss...unless they set the fire intentionally after realising renovations suck / house falling apart (in which case they'd probably knock back donations from friends) or the insurance payout is significantly more than the place is worth...insurance money is only ever the big consolation in said shitstorm. The logistics of re-organizing life, psychological trauma, irreplaceables lost, living out of a motel or rental until the insurance payout and rebuild can pretty much be written off as a difficult and not completely enjoyable chapter in your life. Insurance payout can take 6 months+ too. On the plus side you can realise how few of your hoarded possessions you actually need.

So on that note I would have donated simply so they would have some cash to go and enjoy a vacation or some nice events for a distraction from all that. At the same time, I don't think people should be giving you shit for not donating, that's entirely your choice. The question I always ask (and near impossible to answer) is if they would have done it in return for you.

When I was younger we had a weekend away with a large group of friends and someone broke into the house and nicked a girl's ghd hair straightener and some CDs...well next minute there was a hat passed around to raise funds for a hair straightener. f**k that, I wasn't close mates with the chick and it's a hair straightener, shit happens. Still felt like I got judged for it, though...

I did end up donating though. Some guys were pushing for $100 but not gonna put in that much. Call me hesitant at giving money to someone so they can give money to someone so they can give money to the recipient.
Turns out this guys wife is 4 months pregnant too. Would suck.

At the same time I feel throwing money at things does not solve the problem. Like you said, it's all the shit money doesn't solve that sucks.

VWL ethics time:
ouse burning down, got out of house.
This was over Christmas break, colleaguesfriends heard about the issue. Word spread through


Nowadays everybody wanna talk like they got something to say
But nothing comes out when they move their lips
Just a bunch of gibberish
And motherf**kers act like they forgot about Drez

  • Like 1
1 hour ago, Leroy Peterson said:

I did end up donating though. Some guys were pushing for $100 but not gonna put in that much. Call me hesitant at giving money to someone so they can give money to someone so they can give money to the recipient.
Turns out this guys wife is 4 months pregnant too. Would suck.

At the same time I feel throwing money at things does not solve the problem. Like you said, it's all the shit money doesn't solve that sucks.

I agree. Some problems it solves, others it's just a distraction for - like the exchange of dignity for money when people sue for slander / defamation. Does getting a payout really amend the public embarrassment suffered lol, not at all.

People throw money at things to resolve dissonance because it's easier than physically helping the situation. It's not much different to giving cash as a present. Hence crowdfunding social justice is such a f**king lazy cause: woman gets verbally abused on a bus, nek minute crowdfunded 100k from people because they feel sorry for her and wanna make the situation better from the armchair.

1 hour ago, Leroy Peterson said:

I did end up donating though. Some guys were pushing for $100 but not gonna put in that much. Call me hesitant at giving money to someone so they can give money to someone so they can give money to the recipient.
Turns out this guys wife is 4 months pregnant too. Would suck.

At the same time I feel throwing money at things does not solve the problem. Like you said, it's all the shit money doesn't solve that sucks.

 

I went from the HG to a GTX3076r... safe to say I was like OH YEP OK THIS IS GREAT WHY DIDNT I DO THIS SOONER.
Especially as birdie told me you are running 320kw anyhow.


you brought a borg warner? which one?

Which hypergear turbo did u originally have?

Why did u go from a gtx3076 which u thought was great to a gtx3582?
4 minutes ago, blah_blah said:

 


you brought a borg warner? which one?

Which hypergear turbo did u originally have?

Why did u go from a gtx3076 which u thought was great to a gtx3582?

 

have you ever... EVER seen this guy do ANYTHING logical?

23 minutes ago, joeyjoejoejuniorshabadoo said:

have you ever... EVER seen this guy do ANYTHING logical?

28 minutes ago, blah_blah said:


you brought a borg warner? which one?

Which hypergear turbo did u originally have?

Why did u go from a gtx3076 which u thought was great to a gtx3582?

 

7670 (going to be awhile before it is on, like, half a year)
I had a highflow, then a ATR45 (the one you have)


I went to a GTX3076R because I did not want too much power, I chose this over the HG because I couldn't replicate the results or expectations. I immediately replicated them with the GTX. I chose the GTX3076R because Supra people run them on a 3L, make nearly 400kw and have killer response, which has always been my priority over power.

I went to a GTX3582R because I lost 100RWKW at 5800RPM onwards (between 5800RPM and 6000RPM I literally dropped 100rwkw) so it was clearly choked. So I went the GTX3582 which had a much larger overall power band as I could rev it out. I gained 1500 usable RPM at the top of the rev range, and lost maybe... 300? rpm threshold.

If the GTX3076R choked, why would I be going back to a 7670 which is about the same size? Different manifold, much larger rear housing, and I'm only aiming at about ~320kw. Was pushing 400 through the GTX3076R.

 

4 hours ago, joeyjoejoejuniorshabadoo said:

 


Nowadays everybody wanna talk like they got something to say
But nothing comes out when they move their lips
Just a bunch of gibberish
And motherf**kers act like they forgot about Drez
 

 

Another classic CD for colleagues to vibe with

50 minutes ago, Kinkstaah said:

7670 (going to be awhile before it is on, like, half a year)
I had a highflow, then a ATR45 (the one you have)


I went to a GTX3076R because I did not want too much power, I chose this over the HG because I couldn't replicate the results or expectations. I immediately replicated them with the GTX. I chose the GTX3076R because Supra people run them on a 3L, make nearly 400kw and have killer response, which has always been my priority over power.

I went to a GTX3582R because I lost 100RWKW at 5800RPM onwards (between 5800RPM and 6000RPM I literally dropped 100rwkw) so it was clearly choked. So I went the GTX3582 which had a much larger overall power band as I could rev it out. I gained 1500 usable RPM at the top of the rev range, and lost maybe... 300? rpm threshold.

If the GTX3076R choked, why would I be going back to a 7670 which is about the same size? Different manifold, much larger rear housing, and I'm only aiming at about ~320kw. Was pushing 400 through the GTX3076R.

 

How often do you sit above 5800rpm? What power did the 3076 make before it choked?

Seems to me a 3071 would produce your 320rwkw in a 2.8 on E85 with better response than any of the aforementioned turbos. I mean who cares if it chokes as long as it makes your desired power figure at some point and you have a killer midrange to carry you through the next gears?

I have this argument with everyone who tells me -9s are too small for a GTR and I should go -5s. Sure they will choke up top, but they are still going to be making ~370-380kw as they do so, which is plenty of power in a road going vehicle. Street is not about top end!

Edit: nevermind, re-read your post which is written like a murder mystery and discovered that you've done the return to a smaller / more responsive turbo that will likely choke up top. Welcome to the good life.

I wrote it out because there IS logic in it... But yes I much prefer a fat midrange over peaky top end and always have, especially without AWD.

What works on a 2.5 really doesn't seem to apply to a 2.8 though.

I don't mind it rolling over up top in results you see (like -9s) but mine was much more severe than that, it was really ugly and you could see the whole engine bay glow red from the rear housing.. It was a 'couple dyno runs then cut it short and go home' scenario.

Its possible that over aggressive timing (30-32deg!) Was causing that as well.

Live and learn!

And given that his blown an engine due to massive restrictions on the hotside probably not a good idea to keep the GTX3076 with a dead power band above 5.8k

Reading the BW thread doesnt sound like a 7670 fits stock position? You going highmount or something?

 

There are ways around the small turbo posing a hot side restriction, wastegate setup, rearhousing vs comp housing ratio etc.

Plenty of small turbos used on large engines just for a power boost - most manufacturers run a small turbo harder these days for more linear delivery.

My turbo chokes at 5800 too...but my rear housing is large enough, it's the factory comp housing that does it.

 

17 minutes ago, Birds said:

There are ways around the small turbo posing a hot side restriction, wastegate setup, rearhousing vs comp housing ratio etc.

Plenty of small turbos used on large engines just for a power boost - most manufacturers run a small turbo harder these days for more linear delivery.

My turbo chokes at 5800 too...but my rear housing is large enough, it's the factory comp housing that does it.

 

Yeah probably fine for street use, but for extended times of WOT i.e. the track it wont be good for the engine.

I'm sure Greg will post a dyno graph of his old setup of how atrocious it was

 

Dyno%20GTX3076R%20-%20GTX3582R%20Power.j

The bottom line is the GTX3076R
Note: Car is auto. There is a known (and measured, I has all the sensors) 10% loss through the torque converter in the above graph. So when I say "400kw" I have adjusted that to manual land.

This was at 22psi, on both turbos.. (with vct off/broken at the time)
Point being I doubt many people would keep running the GTX3076R if their topend looked like that on the dyno.

1 hour ago, blah_blah said:

Yeah probably fine for street use, but for extended times of WOT i.e. the track it wont be good for the engine.

I'm sure Greg will post a dyno graph of his old setup of how atrocious it was

 

Track is a different ballgame, however you could still short shift there...if you have a wide midrange powerband you don't need to wring the engine out to make it perform

No different to a large displacement V8 maxing out at 5500-6000rpm, it doesn't need an 8000rpm top end cause torque to boot down low and mid

1 hour ago, Kinkstaah said:

Dyno%20GTX3076R%20-%20GTX3582R%20Power.j

The bottom line is the GTX3076R
Note: Car is auto. There is a known (and measured, I has all the sensors) 10% loss through the torque converter in the above graph. So when I say "400kw" I have adjusted that to manual land.

This was at 22psi, on both turbos.. (with vct off/broken at the time)
Point being I doubt many people would keep running the GTX3076R if their topend looked like that on the dyno.

Top of the graph is 3582 I assume? 

1 hour ago, Kinkstaah said:

Dyno%20GTX3076R%20-%20GTX3582R%20Power.j

The bottom line is the GTX3076R
Note: Car is auto. There is a known (and measured, I has all the sensors) 10% loss through the torque converter in the above graph. So when I say "400kw" I have adjusted that to manual land.

This was at 22psi, on both turbos.. (with vct off/broken at the time)
Point being I doubt many people would keep running the GTX3076R if their topend looked like that on the dyno.

I don't actually see the problem here, besides engine heat (in which case see the below). Yes the turbo is maxing out but the engine is still producing its max power across a 2500rpm band. Smaller turbo is giving about 600rpm better response too. It's not so different to a naturally aspirated dyno graph, which is what happens when you pair a small turbo with a large engine - linear power delivery, falls over up top.

If power is tapering off then so too should boost to keep heat down, straight out the wastegate so as not to pose a restriction for engine breathing. A bigger rear end with the same comp housing I suspect would help this too.

Top is the 3582. This is from a couple of years ago now, the most updated graph is in the Dyno section. (and is 'better')
Point really was explaining why I went up a turbo size was logical at the time.

Since then yes, I'm happier to run less boost/bigger exhaust/better manifold/different exhaust which has all happened since then actually.

But my way of thinking (and Trents, and Scotty who was also there that day) was the standard motor has a rev limit of 7000-7500 functionally, and this thing is very upset at 6000, so it can't really be ideal. I didn't just change it because I have an insatiable lust for MORE POWERRRR for fake internet recognition.

I'd much rather run something less hard and utilize the rev range the motor has/should have. Just feels better than beating the daylights out of a turbo to within an inch of its life. (moreso, I have overspun one of the GTXs!) and short shifting it.


Just didn't seem like the best of plans.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...