Jump to content
SAU Community

Recommended Posts

49 minutes ago, joeyjoejoejuniorshabadoo said:

supplier 2 - but tell work it's supplier 1

pocket $800

 

 

I assure you this thought crossed my mind before any of the altruism and good will

Old Soarer engine is tired as shit, but being a Toyota it'll go for another 100,000km at least. Checked fluids tonight and if the dipstick can be trusted, the oil is overfull - by quite a bit actually - checked it twice with a wiped stick to confirm. I don't remember overfilling it when I last changed the oil. Oil on the stick had a bit of a fuel smell to it, but most tired old engines will do that. Is it possible that fuel is getting past the piston rings and very slowly filling up the sump, hence overfilled?

Does it run at operating temp for a while or barely manage to get up to temp before its parked again?

If it's changing the level on the dip stick I'd check the injectors to make sure one isnt leaking. Did the fuel economy suddenly get worse?

It runs at operating temp, decent sized trips.

Car had been neglected by mother for years (read: rarely serviced and sat parked on side of road for a couple years barely driven), before I borrowed it as a temp car for Leesh to get around in. I've barely driven it myself so haven't been able to track personality changes in it, but it's not a healthy engine - boosts horribly with flat spots etc. blows a lot of smoke - 300,000km on it and that's probably a wound back odo. Fuel economy would never have been great, probably around 13L/100. Smells of fuel so no doubt has a leak somewhere, be it injector or fittings, was just curious if fuel could leak significantly enough to theoretically top up the sump with a hybrid of oil/fuel.

it just depends how bad the leak is if it's changing the level of the sump it's pretty bad, and your oil is probably in very poor shape.

 

Also, fuel leak from fittings and being able to smell it outside the car is basically asking for it to burn to the ground.

 

Would not be driving/10

1JZ no shit

Can't see a leak from fittings, just assuming there could be a slow one given the smell. Think it's emanating from the fuel tank actually, as there is residue near the fuel flap. What could cause that? Seems like the fuel tank is getting pressurised lol

11 hours ago, Birds said:

It runs at operating temp, decent sized trips.

Car had been neglected by mother for years (read: rarely serviced and sat parked on side of road for a couple years barely driven), before I borrowed it as a temp car for Leesh to get around in. I've barely driven it myself so haven't been able to track personality changes in it, but it's not a healthy engine - boosts horribly with flat spots etc. blows a lot of smoke - 300,000km on it and that's probably a wound back odo. Fuel economy would never have been great, probably around 13L/100. Smells of fuel so no doubt has a leak somewhere, be it injector or fittings, was just curious if fuel could leak significantly enough to theoretically top up the sump with a hybrid of oil/fuel.

$50 for the Soarer.

Cash.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

:P 

Birds, leigh:

CSGO majors on next weekend in Poland. might do some live betting. 8hour timezone difference though, makes it a bit tough. might only watch a match or two, but theres always gambling to be had.

https://www.esports-betting.pro/counter-strike-cs-go/pgl-major-krakow-2017/

i've had leaky injectors in the ute so if cars sits for a while was leaking into cyl.

worn rings and it would get past, mine would just run like shit after I come back from a trip till it burned off/spat out the excess fuel.

 

 

42 minutes ago, UNR33L said:

I don't really follow it that much, but it's kinda sad that I know more of those clan names than NBA teams :P

Quietly confident that E-sports will one day be bigger than the NBA

45 minutes ago, Birds said:

Quietly confident that E-sports will one day be bigger than the NBA

Absolutely, there's the on going debate that e-sports shouldn't be called a sport and the players shouldn't be called athletes etc. 

im always amazed at how many smaller leagues or comps there are going at one time just in the international scene. Not sure who watches it all...

Part of the problem is the games. DOTA/LoL/Smite/Heroes Of The Storm. are variations of the same thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...