Jump to content
SAU Community

Recommended Posts

I used aerfoflow hose, can't remember what series. And I did all my water/oil/fuel lines at the same time so I can't really remember.

If you were just to do the soft lines coming out of the fuel tank hat, and in the engine bay I don't think it would be more than $100

Little value in going E85 with std RB25 turbo. E85 is great at allowing you to wind boost into an engine and you are capped at 12-14 psi

Given the expense of going to E85 a HKS 2530 on 98 will be you better results

not entirely correct, you're still able to run loads of timing around the middle of the rpm range without any knock and a few more degrees up top

Meh... It made my car a smidgen laggier but did allow way more ignition. But takes a better calibrated bump than mine to pick that up in back to back driving through the mid range.

But only really made more power as the engine was no longer boost and ignition sensitive so could wind both in.

With a std turbo it will be bye bye exhaust wheel. Though with lower exhaust temp maybe you can run 15-16psi...who knows

No problems with the M35 ceramic turbine, I bumped mine up to 19-20psi on ethanol, for 5 months in between Garrett GTX's. Perhaps the ceramic is glued better on the Stagea? They run 14psi stock.

It was a low K turbo so I suspect it's old age or heat cycles that kills ceramic turbos more than boost or shaft speed. Anyway it's not hard to shove a small highflow core inside it.

In addition if I were to get a upgraded turbo I'd need injectors and a nistune anyway so the only extra expense I'm seeing at this stage is fuel lines, rb25 highflows are quite cheap second-hand and plenty of them around however most say they are too laggy for an rb20

They run 14psi stock.

There's your answer. RB20/25/26 turbos were spec'd to run at 7-10 psi. So they would have been running at a certain shaft speed to achieve that. Try to make 14 psi and they have to go a lot faster. The M35, if standard is 14 psi, will be doing the same sort of sensible speed as the older ones at their standard boost. Wind it up to 19 psi and now you're probably approaching the same sort of speeds that limited the older turbos - just at a higher boost.

It's kind of like how you could get away with running a 25 turbo on a 20 at higher boost levels with less risk of it dying - because it wasn't having to spin quite so fast to make the boost on the smaller engine.

Well my car is about ready to be all put back together and get back on the road. Will be interesting to see how this weekends inspection of tank, lines and filters goes since it has been laying around with E85 in it for 12 months.

I mention that as my car has nothing done to it all to make it E85 compatible. Just 1000cc injectors and in tank pump with Nismo reg. Ran fine like that for 2 years but was driven every 2nd or so day with a tank a week

I've heard stories of the e85 gradually breaking down the stock rubber hoses leading to gunky buildup in the injectors/fuel filter, and as in your case people have left them untouched and it's been fine, honestly if it's a cheap and simple thing to do I don't see a reason not to

Here's an idea, just run whatever boost you run on 98RON safely, then on E85 run the same amount - however just pump in loads and loads of timing till the motor/turbo combination stops making power and back a couple if degrees.

At the end of the day, it's going to still make more power than 98RON, not a totally pointless exercise.

For reference, I tuned my mate's S15 and it made 197kW on 98RON.. when we moved it over to E85 it made 215kW - however it made heaps more mid range power as I was able to pump in heaps of timing into the notorious SR20 timing hole where max torque is achieved.

LOL...Ive actually been following my own advice and I'm up to P14 of the RB20 turbo thread and god dam, kudos have the that HKS on special for 3.14K...http://www.kudosmotorsports.com/catalog/hks-turbocharger-kit-hks-gtrs-11004an008-nissan-skyline-r32-gtst-gts4-r33-gts25t-r34-25gtt-p-1048.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...