Jump to content
SAU Community

Recommended Posts

This is my first DIY so constructive criticism is always appreciated. After much searching online and failing, I thought I’ll write up how to change an RB25DET accessory belts. That is the Air-Con, Power-steering and Alternator belts. If this DIY already exists, all good here is another one.

Disclaimer: I am not a mechanic, I try and work things out using my own knowledge and other peoples DIY to please don’t blame me if anything goes wrong.

Belts I used:
Alternator: Gates Micro-VAT 4PK850
Air-Con: Gates Micro-VAT 4PH915
Power Steering: Gates Micro-VAT 3PK835

Meaning of the numbers:

4: Belt has 4 grooves, this cannot change in the replacement belt
PK: Not sure, don’t think its important
850: Length of belt, you need roughly the same.
All pulley systems have lots of room for adjustment for size of belt so you don’t have to have the exact same one. Have a look at what is currently installed and get something similar in size.

LET THE DIY BEGIN!

Firstly, you need to figure out which belt/s are worn. For me, when I had the steering at full lock with a cold engine, I would get belt squeal as well as when I turned the Air-Con. Therefore I decided to change those, as well as the alternator while I was at it.

When you open the engine bay, you will see your belts such as the pics below.

5_zpsy2qn5xnv.jpg

The the second step is to loosen the alternator pulley which is found on the left side of the engine bay, when facing the car. This will be done by loosening the bolt numbered 1 and then turning bolt number 2. You can then push the alternator towards the engine and loosen it.

2_zpswzcjoiqs.jpg

The next step is the removal of the fan. Using a 10mm spanner, undo the 4 bolts. It helps using WD-40 and then holding a pulley while applying force onto it. Once they are undone, remove the fan.

Once the fan is removed, you need to remove the belt at the very front first. This is the power steering. I believe. To remove this, loosen bolt 3 and then turn bolt 4 to bring the nut away from the holding plate. You can then push the pulley system and loosen the belt. Once loose, the belt can be slid off.

3_zps9ojrbzo8.jpg

The next step is the air-con belt. To remove this, you need to get under the car and remove the underbody protector by removing the 6 screws. Once removed, you will see another bolt near the middle of the car which needs to be loosened. This will allow the tensioner to move and loosen that belt. With the bolt loose, push the tensioner. This might be really tight so use WD-40 and/or a hammer on the block circled, NOT THE PULLEY ITSELF, to move it up. Once this has moved enough, you can pull that belt off too.

4_zpsqonvyfxu.jpg

The last belt to be removed will be the alternator belt. Since you have already loosen it, you can just slide that off too.

Once your belts are off, you can just need to reverse the process and put them back on.

20150928_170135_HDR_zpsaguonbdv.jpg

First alternator belt, don’t tighten this. Next the Air-con belt. Tighten aircon belt tension bolt enough so that belt twists to 90 degrees and nothing more, don’t re-install the under-body protector yet. Install power steering belt and again tighten it so you can just twist it to 90 degrees and tighten the other holding bolt. Next re-install the fan. Once the fan is tight, you can tighten the alternator belt to the same tension.

Start up the car and listen for any noises. Any screeches means the belt it too loose. Power steering will screech at full lock so hold it at full lock for a few seconds. Air-con should screech as soon as you start it if it is loose. Alternator should screech at any point when the car is on.

If any screeches are heard, tighten the corresponding belt using bolts 2, 4 or 5.

Once all belts are tight, you can reinstall the underbody protection as we left it off in case we need to tighten the air-con belt.

Go for a drive and test it out. If any screeching is heard, tighten the belt which causes. Avoid belt squeal eliminators as they are only temporary fixes which make more of a mess than solve the problem.

Final Step: Enjoy your screech-less belts and pulleys :action-smiley-069:!

  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/460031-rb25det-belts-change/
Share on other sites

  • 2 months later...

Nice write up - I looked for a guide ages ago when I did mine and couldn't find any so I just thought stuff it and ended up working it out. A guide would have been nice back then :)

Part of the reason I wrote one up. I thought someone somewhere would find it useful.

  • 1 month later...

Hey man, to tighten the alternator belt do I loosen bolt 1 and adjust tightness with bolt 2? Which way am I suppose to be turning bolt 2 to tighten?

Hey,

Sorry for late reply, I was overseas. Yeah you need to loosen bolt 1 so that the whole alternator moves then turn bolt 2. You want the whole alternator moving away from the middle of the engine so from memory and looking at the picture, it should be to the left to tighten, therefore towards the cabin of the car. It moves enough with each turn to be able to see if its tightening or loosening.

  • Like 1

Hey,

Sorry for late reply, I was overseas. Yeah you need to loosen bolt 1 so that the whole alternator moves then turn bolt 2. You want the whole alternator moving away from the middle of the engine so from memory and looking at the picture, it should be to the left to tighten, therefore towards the cabin of the car. It moves enough with each turn to be able to see if its tightening or loosening.

Thanks mate, yeah took me a while to figure out, was turning both bolts like a mad man and nothing was happening. Had to remove my FMIC piping to get a better view and realised bolt 2 moves the alternator in the slot.

  • 1 year later...
  • 4 years later...
  • 4 weeks later...
On 10/20/2021 at 6:01 AM, Malar1898 said:

This Guide misses a second Bolt at the Powersteering Pump that needs to be loosened to relax or tension the Belt there.

Its the Bolt fixating the Pump and Adjuster-Screw below the #3 shown here.

Thanks for that! I missed that step

  • 1 month later...

Yo man, been reading your living with an R33 thread, big ups on that!


Wanted to ask a question on this thread - my A/C belt only started making a belt slipping noise when the A/C is turned on. The belt is rotating fine when the A/C is off no squeal, does this lead anyone to believe its the bearing for any reason? or could it be the condenser itself having an issue?

  • 3 years later...
4 hours ago, silviaz said:

Does anyone find that they have to tighten their alternator belt once in a while? Mine started squealing again.

Once the belt slips it can very easily cause a cascade that encourages more belt slip. Check the pulleys carefully and see if the grooves have cupped. If it has it's time to replace the pulleys. If the rubber has glazed you also need to replace it. Shouldn't be shiny. From the factory there's a lot of exposed fibers(?) on a v-belt that will go away as it's broken in but some should still remain visible without sticking out significantly like a new belt.

I went through this on my dad's Camry recently. It would keep slipping even after setting the tension higher, only solution was a new belt.

  • Thanks 1
13 minutes ago, GTSBoy said:

You can also get belt dressing in a spray can which can help to settle a belt in that otherwise wants to slip.

Did that last time and it was squealing like mad lol. But my belt was loose at the time. I'll check the tension tomorrow, think I checked it a couple of months ago and was fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...