Jump to content
SAU Community

Recommended Posts

hello everyone

so here is the thing

engine fresh rebuild new rings new bearings done 600km

engine is standard

fuel system standard

afm standard

cams standard

exhaust : tomei manifolds and dumps y pipe + sard high flow cat + 3inch exhaust to the end kakimoto

turbos hks gt2530 with 19psi hks actuators

car wont make more than 330-350 Rwhp on dyno dynamics , full boost is 5k rpm maybe even more

this is not what i expected , we played with timing etc but its stuck on 330whp range and it feals quiet slow untill 6k rpm when drove it and i havnt driven more than 150hp car for past 2 years and still felt slow :)

all dyno graps i have seen are getting more horses and happy with full boost by 4k rpm

anyways some your input would be great

first thinking remove sard cat and put straight 3" cat , do i really need camshafts rght now? i am not planing to go higher boost yet just want get most out 19 psi

thx

Exhaust is choking it for one. It's way too small.

Ditch the lot and build yourself a 3.5 inch system (minimum) with decent (universal) mufflers and try again.

Cams ain't the problem unless when it was put together one of the cams are a tooth out. Seen it before on a mates car.

Rag in cooler piping? Lol

Standard fuel injectors and punp run out of flow at 270kw (360hp)

Standard air flow meters are out of range at 300kw (400hp)

Exhaust needs to be around the twin 3in into a 3.5in with no restrictors in it (most Japanese cat backs have restrictors in the mufflers) put a decent 100cpi cat in it cause the sard ones aren't much better then a factory cat

And put some cam gears in there and use them to get some good gains through the rev range

thx for reply guys

i will remove sard cat and will fit 550cc injectors and see how it goes , not sure why it so late on full boost , mafs and fuel pump should be good for that boost? should i be getting around 400rwhp on 19 psi at list?

forgot to mention egt is 900-1000c , isnt it a bit high?

thx

Why would you just replace the cat when the rest of the exhaust isn't up to the job either? a restricted exhaust will slow down response and send temps through the roof.

The fuel pump is at least 14 years old, do you really want to risk pushing its limits?

If I had 2530s and only making 300kw (400hp) I would say i chose the wrong turbos for my needs

Replace the whole system. Like Brett said above

Why waste time going from 444's to 550's?. Get a set of modern 1000's Atleast.

The reason modern 1000s are being recommended is that there is really no downside, since they respond well at low pulsewidths so idle etc are fine.

For MAFs you can tune past the 300kw limit, but in that range the ECU is guessing what the fuelling should be, so you're risking over or under fuelling. Nismo MAFs bolt in and are good for ~370awkw, which is about that the 2530s make on pump, so would be a good option.

Something is up for sure...

I made 550hp at the wheels on 23psi with a 2.5 inch to 3 inch twin front pipe and a 3 inch blitz nur spec catback. Didn't have a cat though. So exhaust size isn't your issue. Bigger is always better, but its not choking you at that power level if its a healthy flow path.

Collapsed cat?

Power fc,700+cc injectors, decent fuel pump and z32 afms should be on your shopping list for sure. Those turbos are a waste without suporting gear at the least.

Edited by burn4005

Something is up for sure...

I made 550hp at the wheels on 23psi with a 2.5 inch to 3 inch twin front pipe and a 3 inch blitz nur spec catback. Didn't have a cat though. So exhaust size isn't your issue. Bigger is always better, but its not choking you at that power level if its a healthy flow path.

Collapsed cat?

Power fc,700+cc injectors, decent fuel pump and z32 afms should be on your shopping list for sure. Those turbos are a waste without suporting gear at the least.

you see 4psi differensce 200hp more , so thats why i am not happy at all

i do have that list for summer not earlier ;) i just cant do all that stuff right now , r35 mafs , injectors , cams , gears , clutch , pump etc is on summer shopping list not yearlier

thx everyone

just to clear things up , i refresh engine , all gaskets, seals , rings , bearings , reimax pump etc , while engine was getting done i purchsed rutbos and put them on when instaled engine back , my plan was to tune it on stock boost and drive 2-3k km ("brake in time thats how u call it ?:)"). for the summer i would buy all suport mods to push tham to the end . that is why i left stock fuel system on fresh engine , to go high power wasnt my goal .

so car is on dyno and lowest boost it takes is 19psi , didnt think it would be that high , so started tune on 19psi , no boost controller no restrictir removed etc , at the end 330-350 not remember in that range was max we couldnt take out of more no metter what i did . yeah worst part is full boost takes forever to hit !

Ecu is nistune .

all i can do right now is borrow injectors from friend and remove sard cat at all and see were it goes

got recomend to dump my hks iridium spark plags and put ngk bcpr11 ones? maybe i should swap ecu as well? power fc ? i dont know i am just very disepointed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...