Jump to content
SAU Community

Recommended Posts

Hello

I found a rb25det at a used car parts store, its been there for about 6 months or more.

The staff doesnt know if it runs or not.

They only test they did was check to see if the crank turns and take a look at the gears and things underneath the front gear cover.

Is there any way to check the engine besides taking it apart to see it maybe its working or not?

I wouldnt be able to take it apart unless I buy it

Have a beer with it and ask if it's ok

The shop is a well known shop. Anytime they get something that they dont know about, they put in the junk section or reduce the price to a cheap price. If somethings in the junk section, doesnt mean doesnt work, just mean pieces missing, old, or no information on it.

They will usually put whats wrong with something or what condition it is in on the label. Dont think its in the junk section.

This engine they dont know if anything is wrong with it. They did the checking I mentioned earlier.

Not sure if it has their normal one week garuntee on it. If it does, there is no why I can have it put in the car in a weeks time.

Its 650.00 dollars

Edited by yoshiii335

$650 is basically scrap value for an RB25. That's what you pay for one that is or could be broken so that you can use some or all of the parts to fix another one. A good runner here is more like $1500. So it is not a bad risk for you, and you might be able to break it up and sell parts if you were forced to. But you'd be committing to trying to use it unless you do the minimum testing, like a leakdown and see if it will crank and so on.

$650 is basically scrap value for an RB25. That's what you pay for one that is or could be broken so that you can use some or all of the parts to fix another one. A good runner here is more like $1500. So it is not a bad risk for you, and you might be able to break it up and sell parts if you were forced to. But you'd be committing to trying to use it unless you do the minimum testing, like a leakdown and see if it will crank and so on.

Ok

So that means pistons, chambers, valves etc could be messed up or they may not be. Hmm I have to decide if I am going to take that chance. Would buying a working rb25 and building it up be better than buying one that may have to have more parts replaced? Or will it be about the same if I am going to build up the engine?

Car battery, jumper leads to the starter motor and compression test it.

Then compression test again with 5ml of oil in each cylinder and record results

If they're all equal with a delta of 10psi between each cylinder then it will be fine.

The engine should still come with around 3 months exchange warranty, regardless of whether they have seen it running or not. Unless things have changed.

He is in Japan.

Crazy shit applies there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...