Jump to content
SAU Community

Recommended Posts

Mmm lobster...

246380907_c867e08f8a_z.jpg

 

I got the solid rack bushes second hand (unused) Josh...For the life of me cant remember the brand. was BMK or BMR or something like that, They had a website because I checked it out when I bought these but google isnt coming up with anything.

  • Like 1

Started relocating the battery in the boot to make way for some custom tanks.

Ran the cable under the car along with the fuel/brake lines safely out of the way inside some split lock conduit, Comes up into the boot through a cable gland.

cable under car.jpg

cable under car2.jpg

Mounted the battery isolation switch here. (need to get some shorter bolts)

isolator.jpg

Made up a battery mount for my Odyssey Battery (have allowed for some 3mm closed cell foam to fill in the gaps around the battery and under it)

batterymount.jpg

Thats where im up to so far, Battery will be mounted here. Just need to secure that, terminate the cables and she will be good to go.

Battery in boot.jpg

  • Like 2

Cheers Josh... There are billet ones available for a decent price, But this only cost me abit of time and I made it so Im happy.

Finished the battery in boot conversion:

battery fitted.jpg

I used one of these power distribution posts from Jaycar:

single-m10-power-distribution-postImageMain-515.jpg

Fitted it just off to the side of the fuse box (circled red) ran the cable from the battery to there then just connected all the cables that used to run to the battery to that (not 100% happy with it, cables look a little messy so might have to remake the cables from scratch. Just put a rubber grommet and vac cap over it for now... will look for a better cover tho. Heaps of room for me to make a custom overflow/catchcan combo now.

battery terminal.jpg

I got 3 Innovative motorsports MTX-D dual function digital gauges a little while ago... turned out side by side there was not enough space to fit them in the gap of the center console, So had to get a little creative and recess the guages and they juuuust fit. Bolts in place of the factory gauges.

Gauges.jpg

From left to right is #1 Exhaust Gas Temperature, #2 Oil temp (outer ring) Oil pressure (Digital Number) #3 Battery Volts (outer ring) Water Temp (digital number)

Gauge assembly.jpg

Was planning to paint the guage face plate black, but sorta liking the brushed alloy look for now...

gauges fitted.jpg

 

Since im using a Haltech Wide band o2 which is fitted just after where the exhausts from both turbos Merge, to fit the EGT probe I simply drilled a hole in a O2 sensor bung and welded the EGT mount in that and it bolted straight in place of where the stock o2 sensor goes on the front turbo dump pipe. Saved me from having to try remove one of the dumps which would have been a major PITA... Once I convert to single Turbo it will be places Pre-Turbo.

egtbung.jpg

The gauge mount plates are decent but made by hand so measurements are off half a mm here and there and the Chamfer was done by hand so certainly isnt spot on. But was good for a prototype to make sure it all fits up and works properly. So I made some CAD drawings ill send off to be Laser cut in the new year :)

Mountplate.jpg

Faceplate.jpg

 

Hmm what to do next...

 

 

Went for abit of a day trip yesterday, Nice 300km+ round trip to Gordan dam which had some excellent twisty roads through the mountains, Was abit cautious on the way out with the roads being very wet but on the way back they had dried up enough to instill enough confidence to have some real fun :)

gordanrd.jpg

dsc_0146.jpg

fr_1908.jpg

  • Like 3

Ive been here on holidays (last Nov). Windiest road to no-where ive ever taken. Also i think i saw your car at Salamnca place in Hobart. I was so excited i took like 20 photos of your car in the car park. My wife just shook her head...


Tiny update... Got bored the other day and dont use my lathe as much as I would like to so looked for a little project to mess about with and came up with this:

Custom Lighter.jpg

Matches nicely with the Gauge surround being bare alloy for now too..

Custom Lighter fitted.jpg

I don't actually use a cigarette lighter so thinking of stripping the guts out of a USB charger and putting it inside this so I can actually use it.

Also picked up these from ebay, not bad for the price... Thinking of welding on some bits to the side just to make them look abit more beefy, do the job fine tho.

Rad mounts.jpg

And here is a pic of the engine bay just because I dont think Ive posted one before... mainly as its the worst part of the car, But I dont want to paint it until Im happy with the mods (single turbo etc) that way I dont have to stress about paint too much while working on it. engine bay.jpg

  • Like 1
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...