Jump to content
SAU Community

Recommended Posts

37 minutes ago, Dose Pipe Sutututu said:

That's how the NBN is being rolled out lol

lol no, the NBN is being rolled out equivalent to you just saying f**k it and using the cracked o-rings

 

48 minutes ago, Dose Pipe Sutututu said:

So close yet so far, typical NBNish delivery lol.. Over budget and project schedule blown out of the water.

This is EVERY Government funded project

  • Like 1
  • Haha 2
1 hour ago, iruvyouskyrine said:

Those bolts go at the very back of the head on either side. Do you even RB bro?

No :(

I SR20 more lol...

where exactly????

1 hour ago, Dose Pipe Sutututu said:

are those the cylinder head to block bolts that go on the outside??

That's what I thought they were when I saw the pic. I thought there was one front and one rear though not both at the same end?

1 hour ago, Dose Pipe Sutututu said:

are those the cylinder head to block bolts that go on the outside??

Yes correct. 2x M6 bolts

 

38 minutes ago, timmy_89 said:

That's what I thought they were when I saw the pic. I thought there was one front and one rear though not both at the same end?

1 at front intake side and 2 at rear either side.

I should note that i never put them back in any of my engines. With RB25's you can't access the front bolt without taking the inlet manifold off which is a shit job which annoys me as i would rather take the inlet manifold off when the head is out of the car.

15 minutes ago, iruvyouskyrine said:

I should note that i never put them back in any of my engines. With RB25's you can't access the front bolt without taking the inlet manifold off which is a shit job which annoys me as i would rather take the inlet manifold off when the head is out of the car.

Yea they didn't go back on my engine either lol

ahhh I installed coppery colours ones back into those holes.. interesting those bolts I took a photo of, I wouldn't' think they would fit as they're wider than the golden/copper ones I used from the R33 motor.

mad, no fear - didn't fk up

Update but no photos (taking inspiration from @luke gtr lol).

Removed R33 plenum, installed bottom half of R34 plenum.

Now awaiting 1550cc Bosch injectors and a Plazmaman rail. The initial plan was to use the 875cc Siemen DEKA V I had from my old motor but anticipating the power this motor will make there's no way those injectors would cut it, even if I ran 4 bar base pressure.

Been trying to order parts again from Andrew @kudos.motorsports but he isn't replying to my emails :(

 

Update but no photos (taking inspiration from [mention=37584]luke gtr[/mention] lol).
Removed R33 plenum, installed bottom half of R34 plenum.
Now awaiting 1550cc Bosch injectors and a Plazmaman rail. The initial plan was to use the 875cc Siemen DEKA V I had from my old motor but anticipating the power this motor will make there's no way those injectors would cut it, even if I ran 4 bar base pressure.
Been trying to order parts again from Andrew [mention=1172]kudos.motorsports[/mention] but he isn't replying to my emails [emoji20]
 
Nawww, thanks brosef.
1 hour ago, ActionDan said:

Side feed in that boat anchor engine aren't they? 

yeah nah cuz.. I had top feeds in there under the stock plenum before they were even mainstream :)

http://www.trak-life.com/diy-converting-top-feed-injectors-r33-gts-t-skyline-rb25det/

Yah... stainless internals, not modified by any laser cutter/mill/bench grinder/side cutters

US guys usually refer to them as Siemens DEKA V 80lb

I hate modified injectors, those "Bosch 1250cc" are milled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • It's almost certainly a reluctor generating an "AC" waveform. No, ECUs don't generally read those - they're usually set up for PWM square wave 0-5v stuff.
    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
×
×
  • Create New...