Jump to content
SAU Community

Recommended Posts

4 hours ago, Duncan said:

I'm surprised you can hear a properly tensioned timing belt over the fan and injectors, gates or not. I run the gates one in the race car and can't hear it at all. Obviously they would get noisier between the belt and idler/tensioner bearings if over tensioned

You can only hear the difference with the bonnet up or head in the engine bay, can't tell from the driver's seat of the car. In engine bay though they are definitely noticeable as being whirry.

Fk I hate this car... Was trying to figure out why the stupid ABS wasn't working, even though a new relay went in.

Worked out how to put the ABS unit into diagnostic mode and it came up with code 26, LHS wheel speed sensor short circuit.

So sure, let's take off the sensor, give it a clean and trace the wiring back....

FML... Found a molten pile of loom lol... When the motor and bay was stripped and put back together, the loom was run via the OEM location and points. This is incredibly close to where my the gate is. Normal street use, (drag use which it never sees) the loom would have been fine, but on the track it was game over.

Explains why the ABS and tacho all died within hours of each other lol.

Anyhow, wasted 3 hours stripping it back, crimping on new wires, heat shrinking, etc. Will fleece tape the piece of shit and route the loom differently to avoid this same shit storm again.

Buy a Nissan and mod it they reckon 🥲

PXL_20221115_210913365.jpg

  • Like 1
6 minutes ago, r32-25t said:

This is the reason I ran my loom through the wheel arch when I went single 

Initially I had the loom running high up, against the strut tower where the OEM PS reservoir is. 

When the Birrong guys put together the engine bay, and dropped the new motor in they ran the loom in the OEM location with clips and all (not wrong or anything, also probably for them there's no issue too, as most of their customers are drag racers).

The electrical issues only presented themselves after a track day at Luddenham where the loom was exposed to high heat for 10 or more minutes at a time, instead of a whole 10 to 12 seconds.

8 minutes ago, Murray_Calavera said:

Would you consider remaking that section of harness with Tefzel wire? Could even use high temp fiberglass sheathing for added sexiness. 

I want a modern fast car, but my autistic brain will end up with a brand new loom lol.

Like how I said I will never need a built motor or more than 350kW.

  • Haha 2
23 minutes ago, Dose Pipe Sutututu said:

I want a modern fast car, but my autistic brain will end up with a brand new loom lol.

Like how I said I will never need a built motor or more than 350kW.

Like how I say every time I get a new car or bike that "I'm keeping this stock", or my other classic of "while we're in there"

It's a disease, and modifications are the cure

  • Like 1
  • Haha 2
2 minutes ago, r32-25t said:

I reckon fixing your f**k ups would be cheaper then fixing bmws f**k ups 

Go wash your potty mouth out with soap.

BMW would be superb, it will be stock and I will enjoy my life not constantly fixing shit.

  • Haha 2

 

11 minutes ago, Dose Pipe Sutututu said:

Go wash your potty mouth out with soap.

BMW would be superb, it will be stock and I will enjoy my life not constantly fixing shit.

Is that because you’ll be paying out your ass for bmw to fix it?

  • Haha 1

Whether it is a highly modified car, or a standard BMW, you will always need a 2nd car or motorbike to get around in/on

Don't BMW give OPAL card credits when you buy a new one anyway?

  • Haha 2
34 minutes ago, The Bogan said:

2nd car or motorbike to get around in/on

I've got the missus' Tiguan for that, although warranty runs out next July lol... Might be scary driving around in a VW without warranty.

  • Haha 1
3 hours ago, Dose Pipe Sutututu said:

I've got the missus' Tiguan for that, although warranty runs out next July lol... Might be scary driving around in a VW without warranty.

No scarier than driving a BMW still under warranty 

Buy one of these if you want a BMW

Classics

https://www.carsales.com.au/cars/details/1979-bmw-6-series-635csi-e24-manual/SSE-AD-5690775?pageSource=details&id=SSE-AD-5690775

 

https://www.carsales.com.au/cars/details/1989-bmw-3-series-320i-e30-manual/SSE-AD-12906574?pageSource=details&id=SSE-AD-12906574

  • Like 2

Car did not blow up, did find that I dropped the o-ring off the oil cap so there's now a nice oil mist all over the engine bay lol.

Last cruise session, banged the limiter quite a bit in 2nd then spat a PS belt.

Drove car home, I think it was a successful night?

@r32-25t stalker photo below 

IMG_20221119_232301_892.thumb.jpg.e3b372cd73a146b72a45b47853ba08e1.jpg

Managed to do a 2m2s lap on the GP Circuit too inbetween the cruise sessions. Overall, successful day and bumped into a few other SAU members.

IMG-20221119-WA0014.thumb.jpg.584fef228429c9bdab31a9e4b983b506.jpg

PXL_20221119_070912978.thumb.jpg.e5c0cd3a3e2e758a349ca23e4de1afa2.jpg

Over all I think I hate the car less, it's still a croc of shit but not going to lie did giggle a bit 😂

Btw... Rolling antilag is great fun, everyone needs it.

 

 

  • Like 8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...