Jump to content
SAU Community

Recommended Posts

CAR won't start after POD SWAP

So I originally had a BLITZ Pod filter on and decided to change it to a K&N Pod, and it was driving okay till about 20mins after a spirited run, at a red light it jumps into some sort of limp mode where I can't rev it over 2000Rpm even on Neutral. Had to make it home on 40kms. Engine light came on as well :S 

Its a R34 GTT Automatic 98

I have tryed resetting the ECU (battery disconnect) same results.

I then swapped back my BLITZ Pod and now the car won't start at all, could it be my AFM ?? 

 

Edited by Jonic
Link to comment
https://www.sau.com.au/forums/topic/468069-car-wont-start-after-pod-swap/
Share on other sites

You ask for help and then ignore most suggestions. Work methodically and properly eliminate each potential problem. About every third suggestion is the MAF, Did you actually get a new one? If not try this:

http://skylinefiles.blogspot.co.nz/2009/07/how-to-fix-your-rb-afm.html

and if that doesn't help then check the plug.

I just got my new AFM genuine and nope still same problem what a load of shitz, I tried starting without the AFM and it idles perfectly and with the AFM it readjusted itself and stayed on after I plugged it in while the car was running. Still won't let me go over 2000rpms zz

  • 4 weeks later...
2 hours ago, Jonic said:

It was the coolant temp sensor. Everyone is so clueless lol

Considering you created three threads for issues, don't expect further help with attitude like that. Remember, the people on here helping you are regulars and will remember you.

56 minutes ago, niZmO_Man said:

Considering you created three threads for issues, don't expect further help with attitude like that. Remember, the people on here helping you are regulars and will remember you.

my apologies to everyone, i did everything you guys told me but i still couldn't diagnose it and got frustrated cause it felt like I was the only one getting this problem on a Skyline and nothing was working. So excuse my attitude if you guys got insulted in anyway. Peace

11126933_952016398144421_473390593_n.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...