Jump to content
SAU Community

CAR won't start after POD SWAP

Jonic

By Jonic,
in Engines & Forced Induction

 Share

Recommended Posts

Jonic Enthusiast

Jonic

Posted
Posted (edited)

CAR won't start after POD SWAP

So I originally had a BLITZ Pod filter on and decided to change it to a K&N Pod, and it was driving okay till about 20mins after a spirited run, at a red light it jumps into some sort of limp mode where I can't rev it over 2000Rpm even on Neutral. Had to make it home on 40kms. Engine light came on as well :S 

Its a R34 GTT Automatic 98

I have tryed resetting the ECU (battery disconnect) same results.

I then swapped back my BLITZ Pod and now the car won't start at all, could it be my AFM ?? 

 

Edited by Jonic
Link to comment
https://www.sau.com.au/forums/topic/468069-car-wont-start-after-pod-swap/
Share on other sites
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

You ask for help and then ignore most suggestions. Work methodically and properly eliminate each potential problem. About every third suggestion is the MAF, Did you actually get a new one? If not try this:

http://skylinefiles.blogspot.co.nz/2009/07/how-to-fix-your-rb-afm.html

and if that doesn't help then check the plug.

Jonic Enthusiast

Jonic

Posted
  • Author
Posted

I just got my new AFM genuine and nope still same problem what a load of shitz, I tried starting without the AFM and it idles perfectly and with the AFM it readjusted itself and stayed on after I plugged it in while the car was running. Still won't let me go over 2000rpms zz

  • 4 weeks later...
niZmO_Man Grand Master

niZmO_Man

Posted
Posted
2 hours ago, Jonic said:

It was the coolant temp sensor. Everyone is so clueless lol

Considering you created three threads for issues, don't expect further help with attitude like that. Remember, the people on here helping you are regulars and will remember you.

Jonic Enthusiast

Jonic

Posted
  • Author
Posted
56 minutes ago, niZmO_Man said:

Considering you created three threads for issues, don't expect further help with attitude like that. Remember, the people on here helping you are regulars and will remember you.

my apologies to everyone, i did everything you guys told me but i still couldn't diagnose it and got frustrated cause it felt like I was the only one getting this problem on a Skyline and nothing was working. So excuse my attitude if you guys got insulted in anyway. Peace

11126933_952016398144421_473390593_n.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...