Jump to content
SAU Community

Recommended Posts

Rear and Front Windscreen Seals

Hi,

I was just confused about the windscreen seals on my r32 gtr. As seen in the photos (especially the third) the front windscreen seal is not tight. I think its missing a hard plastic layer or something but i'm not sure based off how Nissan has explained it with original part numbers and diagrams. 

If anyone has any info regarding parts and part numbers. Also whether I need to buy OEM parts or a generic seal and where I can purchase these from that would be much appreciated :) 

(For reference pictures 1 and 3 are the front windscreen and 2 and 4 are the rear)

Regards,
Peter

15991361_10211822684780588_334155474_o.jpg

15992286_10211822686220624_1456129435_o.jpg

16009834_10211822684900591_1784574987_o.jpg

16106517_10211822686140622_935177181_o.jpg

Link to comment
https://www.sau.com.au/forums/topic/468589-rear-and-front-windscreen-seals/
Share on other sites

Callan is correct ^

Search RHDjapan for original part numbers. There is even recent threads on here with all the info you need.

Generic works but you loose the original look/authenticity.

Any car window fitter will have aftermarket generic windscreen rubbers (like O'briens).

Yep...... Unfortunately these parts are getting very expensive:

This is what you need, one of each. Then you need to pay to get an installer to fit them. Don't expect much change out of $2K for the lot fitted.

I searched high and low from various suppliers to get a complete set 6 months ago and it owes me over $1300.00 plus fitting.

Cheers,

Bob.

  • Front Windscreen Mould Set
72750-04U60  
  • Front Windscreen Fastener Set
72725-04U19  
  • Rear Windscreen Mould Set
79750-04U10  
  • Rear Windscreen Fastener Set
79780-04U15  

Just checked Amayama website, they want $551 for front mould set and $897 for rear mould set plus postage but both front and rear fastener sets are discontinued.

This is a classic example of how important it is to get parts when you can because R32 parts are getting very hard to source.

Bob.

I'm still kinda unsure how the windscreen seals work in comparison to getting just your typical fitting rubbers from O'Briens for example. It seemed like on the car as if the windscreen rubber that is current on was fitted within the gap and as it heated and overtime etc it expanded and what not and became unstuck. Does the OEM have a harder plastic seal over the top or something?

I also saw something like this
http://www.ebay.com.au/itm/SELLING-ALL-MY-R32-GTR-STUFF-THIS-AUCTION-FRONT-WINDSCREEN-SURROUNDS-BNR32-GTR-/272485217962

Weighing up the options on whether to go OEM or just use the spare cash for other things that need attention like original seats etc

Thanks for the info btw Bob, ill send you a message to get in touch in the next few weeks when I get a free weekend off work etc

That link - They're useless unless you have the fastener set which you don't. Those are metal and clip over the top.

The fasteners are put in when the windscreen (f/r) is out at time of manufacture. Then the window is placed in and the mould set applied.

The typical fitting rubber seals don't come out when done properly. I except yours was just bodgy job in the first place. People get what they for.

.

8 minutes ago, Sinista32 said:

That link - They're useless unless you have the fastener set which you don't. Those are metal and clip over the top.

The fasteners are put in when the windscreen (f/r) is out at time of manufacture. Then the window is placed in and the mould set applied.

The typical fitting rubber seals don't come out when done properly. I except yours was just bodgy job in the first place. People get what they for.

.

100% correct........... There is "any old way" or the correct way!

  • 3 weeks later...

Hi Peter.

I recently went through this exercise and was able to source all OEM parts from Andrew at Kudos Motorsports - http://www.kudosmotorsports.com/catalog/index.php.  I recommend getting in touch with him as he has a fantastic selection of parts and most are usually available immediately.  He and his team are also brilliant to deal with, offering great service.

Cheers,

Mark

  • 4 years later...
On 1/12/2017 at 6:48 AM, 21PC said:

Rear and Front Windscreen Seals

Hi,

I was just confused about the windscreen seals on my r32 gtr. As seen in the photos (especially the third) the front windscreen seal is not tight. I think its missing a hard plastic layer or something but i'm not sure based off how Nissan has explained it with original part numbers and diagrams. 

If anyone has any info regarding parts and part numbers. Also whether I need to buy OEM parts or a generic seal and where I can purchase these from that would be much appreciated :) 

(For reference pictures 1 and 3 are the front windscreen and 2 and 4 are the rear)

Regards,
Peter

15991361_10211822684780588_334155474_o.jpg

15992286_10211822686220624_1456129435_o.jpg

16009834_10211822684900591_1784574987_o.jpg

16106517_10211822686140622_935177181_o.jpg

Any idea on what rubber types/styles these are? trying to get myself a set please, thanks.

  • 2 years later...

Hi Denis, per earlier in this thread (and there is similar info elsewhere), it is unlikely you can get factory seals and clips and will have to go generic replacement.  Even if you can get hold of all of the factory moulds the clips that hold them in are not available and yours are almost certainly broken by now.

So, all you need is a competent installer who can fit generic seals. The last 2 times I had the seals done, they were not done correctly and came loose (1st time) and are fitted fully but don't sit very well (2nd time).

Sorry there doesn't seem to be a better solution out there. Of course, if your retaining clips are not amazingly broken, you can try and refit the factory trims.

On 17/01/2024 at 7:59 AM, Denis said:

searching for a windscreen fitter familiar with r32 moulding fastener install, finding it difficult to maintain alignment to body in corner sections, leaving a gap on install. canberra 

Hi @Denis,
I recommend that you contact Michael at Metro Auto Glass who is very experienced with BNR32 installations and who has installed OEM fronts and rears for me personally.  He is Sydney based but may be able to assist you.
 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...