Jump to content
SAU Community

Recommended Posts

V35 Drag Racing

Hi everyone,

As we are all aware, there are plenty of videos out there of R series Skylines running the quarter mile, but not a lot about the humble V35 350 GT. For obvious reasons, they are not often considered for drag/track applications, especially against other boosted JDM imports.

When the Perth Motorplex held a Nissan VS Honda theme night (not a fair match-up, I know...) in March 2017, where you could run your Honda or Nissan for $20, I thought "bugger it", and decided to give it a crack.

Ill start with a bit about the car first- My Skyline is a 2003 coupe, with a 5 speed A/T gearbox. I have owned the car for 2.5 years and am the first Australian owner. It has the following mods- Tein coilovers, Godspeed front/rear sway bars, vented/slotted rotors, Injen CAI, Mace engineering 12mm plenum spacer and an Apexi 3" catback exhaust.

I did a fair bit of research prior to running. According to "experts" on G35 Driver, they should be running around 14.7 dead stock. I was expecting 14.4 to 14.5 based on my mods, if these "experts" were correct. Boy was I surprised- my first run, with my brother riding shotgun and a full tank of fuel, netted a disappointing 15.050 @ 150.46kph, in full automatic mode (with power set to on). I also forgot to turn off VDC until my third run, which may have also cost a bit of time.

For the next run, I booted my brother out of the car and saw an immediate improvement to 14.860 @ 152.67 kph. Still disappointing, but I knew I could definitely shave a bit of time by shifting manually as the car was shifting into 4th just before the finish line. I knew if I held it in third, I could squeeze a few extra kph out of it.

I decided to let my brother have a run next as per the video below. We still lost, but we were constantly seeing improvement in each run. I believe he ran a 14.8, which was excellent considering I was in the car. He had an excellent launch too.  Apologies in advance, as there is a bit of coarse language. 

 

 

 

My third run suffered from a boggy launch, and a limiter bash in second, so I only managed 14.975 @ 153.87 kph. I cant blame my brother for that one, as he wasn't in the car.

My last run was the best of the night. My brother captured it on his camera, so I will link it in the comments once I have obtained it off him.

My final run was 14.678 @ 156.03 kph. My car had finally achieved (and slightly bettered) what the "experts" said it should have done. I was very happy with that run, and decided to call it a night. I let my brother have another run, where he managed 14.7xx (again, I will link it in the comments once I have transferred it). By the end. I was fairly happy, especially when I learned that the two 350z's that were there only managed mid to low 15's. 

Is there room for improvement? 

For sure.

Perth temps suck at that time of the year in the early evening. The temp was still in the mid to high 20's and it was humid as buggery. As many of you will agree, these conditions have a detrimental impact on performance on our cars. I also went down with a full tank of fuel- this would be the equivalent of carrying another passenger in the car. Considering I gained 2/100ths of a second by dropping a passenger, another run with low fuel and colder temps could see a considerable improvement. I may even possibly see the 14.4 or 14.5 I was chasing.

When I uploaded my video to Youtube, I came across a few G35 and 350z quarter mile runs, and they were all running in the 15's. It just goes to show that you cannot always believe what you read on the internet, and that a "textbook" run is something that trained drivers achieve under ideal circumstances.

I hope this info helps, as there was not a lot out there about what these cars can do.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/
Share on other sites

Nice wright up bro.

I wish i had taken my V35 down to Perth and did some runs when i had mine. I always believed it could get into the 13s. But i'll never know, unless the next owner takes it.

 

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7825284
Share on other sites

  • 4 weeks later...

So, just an update. I decided to give it another crack under better conditions to see how it went.

I went down on a chilly night on 10/05/17 after doing the 100k service (new plugs and oil) and saw massive improvements. Best run of the night was 14.3 @ 158kph. I was much happier with this result, especially since it's only a mildly modified car. I beat 2 R34's and an R33, and the look on all their faces at the end was priceless. Terminal speed could still do with some improvement (across all runs, the turbo skylines had a final speed at least 10kph faster than me).

I'm fairly confident some HFC's, headers and an uprev tune would see me break into the 13's. The car really lacks at top end. Another V35 was there that night, and was running 14.7-9s, and a 350z was running very low 15's but was unable to crack the 14's.

time sheet.pdf

Edited by camr33
  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7831859
Share on other sites

100mph term speed 160kmhr is usually around a flat 14 so im not sure how much better you can "drive" it to reach the maximum - you pretty much are dirving the max of the car's potential.  Colder weather, tyre pressure might make a slight difference - diff ration could also help get into the 13's - new tyres.

either way 14.3 is v good for a auto

Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7832109
Share on other sites

Yeah, I was very happy to run 14.3. I increased my tyre pressure to around 36psi (from about 30), so I'm wondering if this helped. I had no traction issue either time, which is why I decided to run it a bit higher. Rear tyres were brand new Achilles, which were recommended as I was having traction issues in the wet.

My first night was 14.6 @ 156kph and second night was 14.3 @ 158, so there was only 2kph difference despite a fairly big time gap. The time sheet showed a similar 60ft time, but the 660ft speed was about 4kph difference. 

Overall, it didn't seem like a particularly fast run either, but I dont think it would have managed much faster TBH. The terminal speed was about .5kph slower than another run i did that night, so a 159kph pass would not have been out of the question. I think I have launching down good, as well as manual shifting, but 3rd gear is where the turbos seemed to have their advantage.

Overall though, I'm proud of the result.

 

Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7832163
Share on other sites

Good work!

I reckon next mod do HFCs and other exhaust mods (Y Pipe, Mid pipe etc).

Going by the research I have been doing, doesn't seem Headers (though it does make an improvement) are worth it for the price v gains. Though if I got a set of Tomei Expreme V2 for dirt cheap I probably would lol.

I'd say your 3rd to 4th will be quicker with HFCs etc, I noticed my mid to top range improving after getting some.

Then maybe tune. :1311_thumbsup_tone2:

Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7832171
Share on other sites

  • 2 weeks later...

My mate managed to run 14.3 in his VE SS commodore a few years ago, with a terminal speed of 162kph. So clearly my top end is hurting me (still pretty stoked that a car with a 60kw+ power disadvantage could manage to keep par). I noticed last time around, the car was about to redline as I crossed the finish, whereas the first time I went, it was sitting around 6000rpm. I would definately say I have reached the limit of what the car can do at this point of time.

Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7834108
Share on other sites

  • 2 weeks later...

What tyres and sizes are you running? what wheels? Making sure the alignment is up the scratch can help a lot too (no camber in the rear, or minimising camber when squatting on launch).

With an auto, I think a shift kit will improve the car dramatically. I think it would be noticeable on a timeslip due to the quicker change between gears and not the soft/sluggish overlap between 2 gears.

I'm not too cluey on the 5-speed autos, but MV Automatics in SA should have a decent kit available for it?

Good on you for keeping at it.

Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7835924
Share on other sites

Running factory forged Rays 19x8/19x8.5 wheels. Cant remember the exact type of tyres, but they were Achilles that a lot of clubsport owners tend to use. Have considered a shift-kit in the past, but can't see it make a huge difference TBH.

Edited by camr33
Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7835994
Share on other sites

1 hour ago, Leroy Peterson said:

Don't knock a shift kit until you've driven a good one. Even if not for the drags, the difference on the road is night and day.

Great for those short stubby arms :9_innocent:

Link to comment
https://www.sau.com.au/forums/topic/470135-v35-drag-racing/#findComment-7836035
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...