Jump to content
SAU Community

Recommended Posts

1 hour ago, Mick_o said:

Lol .63 on a 3L?! You have alot to learn young Jedi... Measure your turbine pressures or flog your car for a while and see how long the head stays on it with a .63? 

Depends what your doing with it, mines not corked at all, keeps making power past 7500rpm, its a street car and wont see a track to be flogged non stop, if its only street car then id rather it have more low end as id rarely hit 7500rpm on a local street.

43 minutes ago, AngryRB said:

Depends what your doing with it, mines not corked at all, keeps making power past 7500rpm, its a street car and wont see a track to be flogged non stop, if its only street car then id rather it have more low end as id rarely hit 7500rpm on a local street.

I guarantee you wont make more low end with a smaller turbine.

Trying to bring boost on early doesn't make more power earlier. 

If your engines exhaust gases cant get out due to a small turbine restricting flow its gunna lose power down low and produce less torque off boost when putting around on the streets off boost. 

 

  • Like 1
2 hours ago, AngryRB said:

Gt3076 0.82 on my 30, plenty big enough, could even go down to 0.63 as still takes some revs to wake up.

Road use, the 3076 0.8A/R combination is damn hard to beat.  They pull down around 2000, and run up to 7000 without falling over.  They're not magical, but it's tried and proven.

If it's track, go to a 3576 0.8A/R.  Provided you're wearing blinkers and only want Garrett.  As per Piggy's comment, you need to let it breathe out.

  • Like 2
3 hours ago, Griffin said:

I'd imagine a .82 on 3576 would work much better.

Would be a good set up but if you're looking to make over the 400kW Mark I would seriously jam a bigger rear on.

Once I outgrow my turbo I may look along those lines however a GTX3576 with a 1.0x ish rear and twin scroll everything - blah blah blah lol 

2 hours ago, Dose Pipe Sutututu said:

Would be a good set up but if you're looking to make over the 400kW Mark I would seriously jam a bigger rear on.

Once I outgrow my turbo I may look along those lines however a GTX3576 with a 1.0x ish rear and twin scroll everything - blah blah blah lol 

I'm not looking for 400+ out of this as it's just a stock low km bottom end. It's in a cefiro . About 350 would do

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...